How to replace the heating element on an Ariston washing machine
There are certain signs by which you can determine that the heating element has stopped working normally, for example, the water does not heat up during washing. To do this, just touch the loading hatch 10–15 minutes after starting work. If the heating element is working normally, the sunroof will be warm. But, if the hatch remains cold, then it makes sense to think about replacing the heating element on the Ariston washing machine.
Causes of breakdowns?
Failure of the heating element is one of the simplest failures that occur in Hotpoint Ariston washing machines. To eliminate it, there is no need to completely or partially disassemble the machine.
Most often, the heating element is to blame for stopping water heating, but there are cases when the wires that connect to it are also to blame. Therefore, the performance check begins with them.
TEN – stands for tubular electric heater. It consists of a metal tube and wire, which actually heats up. It should be noted that the wire experiences certain overloads when heating and cooling, and this leads to its failure.
Another reason for heating element problems is scale formation. It prevents the water from heating and leads to overload of the heating filament. By the way, scale can cause serious harm not only to the heating element, but also to the drum. This process cannot be completely eliminated, but it can be slowed down using special chemicals.
Sometimes the control device or incorrect operation is to blame for the lack of water heating temperature sensor. The presence of these problems can be checked using a tester.By the way, with its help you can identify the malfunction of the heating element with your own hands.
Preparation for repair
Replacing the heating element on a washing machine is quite simple, but this work can only be done after certain preparation. It is necessary to disconnect the machine from the electrical network and water supply. This will ensure the safety of repairs.
For the convenience of the worker, it makes sense to move the machine to a more spacious place. Before replacing the heating element on an Ariston washing machine, you need to assemble the following tool:
screwdrivers;
tester;
spanners;
pliers.
Important! It is better to buy a new heater by going to the store with a dismantled heating element, and use it as a sample.
Work order
How can you remove the heating element in an Ariston washing machine? First you need to determine the installation location of the heating element. In the washing unit from this company it is located on the rear side of the machine body. The exact installation location can be determined by the wires to which the heater is connected. The heating element itself is mounted inside the machine; only the terminals are visible on the outside.
In models of this brand, heaters are usually installed behind a small hatch, which is located on the back of the device. The hatch cover is attached to the body with hardware, and by removing it you can immediately gain access to the heating element. Using the prepared tool, you must disconnect all wires and the temperature sensor. After this, you can begin to remove the heater from the machine.
Before you remove the heater, you must remember to drain the water. In order to remove the heating element in the Ariston washing machine, there is no need to unscrew the central nut, you just need to loosen it.After this, you can push the pin inside using a pre-prepared tool.
After draining the water, it makes sense to check the condition of the garbage filter, especially if you know that it has not been cleaned for a long time.
When pulling out the heating element, we must not forget that an insulating gasket made of rubber is installed on the seat, and it prevents it from being removed. Therefore, using a slotted screwdriver, you need to pry up the gasket and carefully remove it from its place.
You must be prepared for the fact that it will be difficult to remove the heating element. In some cases, it needs to be rocked in different directions for a long time and pulled towards itself before the part gives way. Be careful not to break off the contact or damage the gasket.
After removing the heater and purchasing a new part, you can begin installing it. To do this, the heating element must be inserted into the vacated hole. In some models, a special support is installed for the heater. After this, you need to secure the central nut and connect the wires. It is not recommended to tighten the nuts with excessive force.
To test the replaced heater, it is necessary to connect the disconnected communications in place and run the machine in idle mode, setting the water temperature within 60 - 80 degrees. In this case, you need to regularly check the temperature of the loading hatch; if the installation of the new device is carried out correctly, then after a while the plastic will become warm.
There are certain signs by which you can determine that the heating element has stopped working normally, for example, the water does not heat up during washing. To do this, just touch the loading hatch 10–15 minutes after starting work. If the heating element is working normally, the sunroof will be warm. But, if the hatch remains cold, then it makes sense to think about replacing the heating element on the Ariston washing machine.
How can you remove the heating element in an Ariston washing machine? First you need to determine the installation location of the heating element. In the washing unit from this company it is located on the rear side of the machine body. The exact installation location can be determined by the wires to which the heater is connected. The heating element itself is mounted inside the machine; only the terminals are visible on the outside.
Add a comment