How to change the drain pump on an Atlant washing machine?

How to change the drain pump on an Atlant washing machine Long-term operation of an automatic machine often leads to breakdown of the drain system. The problem can be indicated by the corresponding error code detected on the device display. Replacing the drain pump on an Atlant washing machine is not a complicated process, so you can do this work yourself. You can order all the necessary parts and a new pump directly from the machine manufacturer, or purchase it in specialized stores.

Do I need to “touch” the pump?

Before replacing the pump, you need to identify its malfunction. To do this, we carry out independent diagnostics of the operation of the washing machine itself, its internal parts and elements. Since, in addition to a breakdown of the drain pump, there may be other problems with the operation of the washing machine that require minor repairs or complete replacement of parts.

Pay attention to the “full” implementation of the specified washing programs by the automatic machine itself. Almost all modern equipment is equipped with a self-diagnosis system. In the event of a malfunction, the washing machine will notify you with the appropriate code, which will be revealed on the digital display. All possible combinations can be easily deciphered using the instructions for the equipment, which will help to identify the primary cause of problems in the breakdown of the drain system.

Important! A breakdown of the drainage system is characterized by stopping the washing program at the water drainage stage. The device freezes and after several attempts shows an error on the screen.

Initially, check the set spin mode and its inclusion in the specified program. If it is missing from the program or has been reset, then connect it again.The next step is to check the external drainage system: the hose should be located above the level of the tank, without bends or signs of compression. If the hose is positioned correctly, in accordance with the instructions, then it is necessary to check the filters for clogging by disconnecting it from the water pipes. Direct the hose into the sink, bathtub and turn on the spin cycle. If the machine discharges water freely, then the reason is that the filters are clogged. Otherwise, the problem is in the drain pump of the washing machine.

If the problem is clogged, then the filters need to be cleaned. To do this, remove the protective panel located at the bottom, in front of the case (it resembles a small hatch). Prepare a special container for the liquid, suitable in size and volume. Unscrew the drain filter and drain all the water. Clean the inner walls and the filter itself from excess dirt. start by cleaning the filter

Inspect the inside surface with a flashlight. Check the rotation of the impeller - if it rotates freely, then there are no problems with the pump. If it is static or difficult to rotate, start checking the pump for its serviceability.

Repair instructions

Atlant washing machines do not have complicated internal structures, so you can change the pump or any other part yourself. To carry out repairs, it is necessary to study all the nuances of the design and further work, have enough free time and a minimum of necessary tools. To change the pump, there is no need to remove all parts from the device, remove the housing, etc. The pump is replaced through the bottom of the machine, following a certain algorithm:

Disconnect the device from power. Drain all the liquid from the tank of the automatic machine, close the fill valve;
lay additional material on the floor to protect it from moisture (a blanket, thick cardboard, etc. will do), place the device on its side;

Important! Position the washing machine so that the pump is at the top. This will prevent possible difficulties in removing internal elements.

Unfasten the panel from the bottom of the machine by unscrewing the screws or loosening other fasteners;
Disconnect the drain pump from its base. The elements securing the pump are located near the drain valve;
press the pump away from the drain valve and carefully pull it towards you;
disconnect the power cables from the pump;
drain the liquid remaining inside the pump by removing the drain plug. Check the snail for serviceability. If it is completely intact, then attach it back together with the new pump. To disconnect the pump housing, unscrew the bolts securing the pump, then remove the connecting elements.
Remove accumulated dirt from the snail. The side in contact with the new pump must be perfectly clean;
insert the drain pump and volute into their base;
install a new pump, connect to the existing wiring.

Replacing the drain pump with your own hands is not difficult. The main thing is to have an idea of the internal parts of the Atlant automatic machine and the skills of simple repair work. If replacing parts of this equipment raises a lot of questions and misunderstandings, then it is better to contact a specialist for repairs. This way you will prevent more serious and expensive breakdowns.