Washing things in a washing machine involves using instructions that indicate certain steps to perform before washing and turning on the machine. That is, open the tap before washing and close it after washing. If we consider this situation from a safety point of view, then everything is correct, but such actions lead to rapid wear and tear of the crane. The fact is that such devices are not of high quality, so they quickly break down. In this case, the tap is designed for a certain number of openings/closings. In this regard, a completely reasonable question arises: how to replace a faucet for a washing machine that has begun to leak?
What kind of faucet do you have installed?
In most cases, craftsmen install a ball valve. There are three main types of such cranes.
For example, a walk-through valve can be installed that has special holes on both sides. At one end this tap is connected to a water pipe, at the other end the inlet hose of the washing machine is connected to it.
Another type of valve is a tee valve or, in other words, a three-way valve. This product is distinguished by the fact that it has three inputs and outputs. One hole is intended for the inlet hose of the washing machine, and the other two are responsible for combining the water supply outlets into a single structure.
These elements can have their own parameters, shape and system. They are used for tapping into water pipes. There they are integrated with other devices, including the mixer.
An angle valve system is similar to a straight through fitting, there are features that match these elements.Using this crane, specialists divide the pipe into two parts located at right angles.
This component is used during the installation of a toilet, although craftsmen also use the faucet for washing machines that are connected to the system in a non-standard way. Along with the faucet, the kit includes seals, special nuts, and handles. Rotary handles are designed to shut off the water. The component is attached to the part with a special nut, the system is very simple.
Removing the old and installing a new faucet
Before purchasing a new faucet, you need to inspect the old one. Experts recommend purchasing a similar option so that there are no problems with replacement. However, it is best to buy a high-quality, reliable and expensive fitting so that after a while you do not have to change it again. First of all, you need to select an open-end wrench; it must match the parameters of the nut. But you can also use an adjustable wrench. Also during the work you will need FUM tape.
The instructions for replacing the faucet look simple.
At the very beginning, you should disconnect the washing machine from the network, and then turn off the water.
It is best to unscrew the plastic nut by hand so as not to break the product. It is necessary to place a basin in the place of analysis.
There is a special seal inside the plastic nut; it is worth checking. If it is faulty, it must be replaced.
You can unscrew the nuts using an adjustable wrench; the old tap is removed in the same way.
Before installing the purchased faucet, you need to clean the threads from adhering dirt. Only after this can the seals be put on and the tape wound.
Next, we install an expensive faucet, the handle of which should be in the “Closed” state.
A plastic nut must be screwed to the free outlet; it is directly connected to the inlet hose of the device. It is best to perform these actions manually so as not to damage the plastic, otherwise it may burst.
At the very end, it is worth checking the operation of the tap; it should not leak. A leak may appear after some time, so you should allow at least fifteen minutes to check. If the faucet is leaking, you need to turn off the water, unscrew the faucet, change the winding and reinstall the faucet.
The replacement is successful if everything is dry at the work site and the tap opens/closes perfectly. Experts advise installing an expensive, high-quality and reliable faucet, then the product will last for a long time.
Washing things in a washing machine involves using instructions that indicate certain steps to perform before washing and turning on the machine. That is, open the tap before washing and close it after washing. If we consider this situation from a safety point of view, then everything is correct, but such actions lead to rapid wear and tear of the crane. The fact is that such devices are not of high quality, so they quickly break down. In this case, the tap is designed for a certain number of openings/closings. In this regard, a completely reasonable question arises: how to replace a faucet for a washing machine that has begun to leak?
How much does this kind of work cost?