Powder tray leaking in LG washing machine

LG washing machines have disadvantages, one of which I will discuss in this article. During their use, such a defect often occurs - water flows from the powder compartment of the washing machine. You can cope with this problem yourself, without resorting to outside help. It is not difficult, does not take long and does not require special skills and knowledge or special qualifications. Contacting the service department in such a situation will cost a pretty penny, so in order to save money, we will do everything ourselves completely free of charge.

Causes of failure

Before repairing the car, you need to understand the cause of the problem and localize it. A leak in the washing machine powder receptacle may be a manufacturing defect or may occur over time due to abrasion of certain parts. Leaks can appear in various places, namely:

1. The perimeter of the tray in the area where its top and bottom meet. To make it clear, I’ll make a reservation right away: a tray is the part into which a container for washing powder or gel is inserted. It's the joints that are leaking.
2. In the area where the tray joins the front of the machine.
3. The hole above the container into which the powder is loaded. This happens because the sliding part wears off over time during use, or rather, the elements that hold it pressed to the top of the tray wear out.
4. A corrugated rubber hose through which the powder is washed out of the tray into the drum.

There is one peculiarity here. This corrugated tube is positioned so that its lower part slides over the balancing stone and rubs against it, causing a hole to form. It is possible that this was done intentionally.

Today, many manufacturers, trying to increase cash flow, strive to ensure that their products wear out immediately after the expiration of the warranty period. And they had to be repaired or bought new ones. And what do you want? This is business!

What is needed for repair?

Before we begin the repair itself, we will prepare everything that may be needed. Nothing special is needed. Usually everything you need is available in every home. You will need these tools:

• flat and Phillips screwdriver;
• pliers;
• file;
• hacksaw for metal.

In addition, you will need silicone sealant or washing machine sealant. You may also need a new tray, because not everything can always be repaired; sometimes you have to replace it. But you shouldn’t stock up on them; it’s better to understand whether there is a need for it or whether you can repair the old one.

Troubleshooting

First, try to determine the place where the tray is leaking. But don’t be discouraged if you can’t immediately figure out where the tray is leaking. You will certainly find out this when you disassemble the machine.

Open the powder compartment, press on the central compartment and take out the drawer. Using a Phillips screwdriver, unscrew the screws that secure the tray. Now let's work on the cover of the machine. On the back wall we find the screws that hold it in place and unscrew them with the same Phillips screwdriver.

Important! We are in no hurry to remove the lid. First we move it as shown in the picture. And only then do we raise it.

The lid was opened. Now we remove the hoses coming from the tray (there are 4 of them). Immediately visible are only 2 hoses through which water flows, attached to the back of the tray. Another one, for air removal, is fixed to the right, it is also not difficult to find.You will see the fourth hose, a thick corrugated tube, on the left side by slightly moving the tray to the right. He then rubs against the stone.

To remove the hoses, use pliers to move the clamps, after which the tubes can be easily removed. Then we pull out the tray itself. We carefully inspect all removed parts. If there is scale somewhere, remove it with water and a cleaning agent, this will allow the machine to work longer.

If a thick hose is worn out, you will have to order it from a service center. You can't fix it yourself. To prevent this from happening again, craftsmen advise sealing the stone with a thick layer of cellophane or soft plastic in the area of ​​contact with the hose. After this, it is better to fill this place with sealant so that the structure holds better. Now we open the compartment, using a flat screwdriver to move away the clamps to process the joints. Having opened the compartment, we spray the seams with sealant to eliminate the leak.

After all these procedures, we assemble the machine in the reverse order. One more tip. Align the machine so that it is level and vertical using a level. Or at least eliminate the forward bias. These simple steps can also help get rid of the leak.

4 reader comments

1. 08/19/2019 at 21:55

   Sanya:

   Where is that thick hose?

   Answer
2. 05/14/2021 at 17:15

   Fox:

   He's inside, bro.

   Answer
3. 05/30/2021 at 19:03

   Vasya:

   Thank you, your advice helped, I removed the powder compartment. I clean it in lemon juice.

   Answer
4. 02/13/2022 at 00:47

   Inna:

   Thank you very much! I cleaned the tray with limescale remover and now the leaking has stopped!

   Answer