How to care for your Indesit washing machine?

How to care for your Indesit washing machine Modern Indesit washing machines operate almost entirely in automatic mode. Users only need to load laundry, select a program, add detergent and press the “Start” button. True, there is one “but” - no one can cancel machine care. In order for the equipment to last longer and without breakdowns, it is necessary to organize proper care of the Indesit washing machine. Specific recommendations and instructions will help you cope with the task.

Basic rules for caring for equipment

It’s easy to increase the service life of your washing machine – all you need to do is properly care for your washing machine. There is no need to make any special efforts, since we are talking about banal hygiene and cleaning. The main thing is to do this regularly and diligently.

First of all, it is important to monitor the body of the washing machine. It is recommended to wipe the machine with a sponge soaked in an alcohol-free care product every 3-5 days. We do the same when fingerprints, powder and dust appear on the washing machine. All this will protect the white plastic from premature yellowing.

The cuff also requires care. After each wash, wipe it dry with a cloth, and wash it with a simple soap solution once a week. Cleaners, solvents and aggressive agents are prohibited as they can damage the rubber.

After finishing washing, it is recommended to wipe the drum and hatch door dry and leave them open for free air conditioning.

The dispensary - the tray for detergents - must be washed. It is better to remove undissolved powder immediately after washing, otherwise the mixture will harden and clog the pipes.Warm water and an old toothbrush are sufficient for cleaning.

It is also easy to care for the drum. The basic rule is to leave the hatch open after washing. It is also important not to accumulate dirty laundry inside the washing machine, but to turn clothes with metal decoration inside out and place them in special protective bags. after washing, remove the tray and open the door

The drainage pump does not require special care. Modern washing machines are equipped with self-cleaning devices that start cleaning as scheduled. But the casing located next to the pump often becomes dirty due to hair, small debris and wool getting into the drain. It is cleaned monthly: to do this, we remove the front wall, remove the lid and carefully clean out the accumulated debris.

Before each wash, check the integrity of the inlet hose - cuts, squeezing and cracks will lead to sudden detachment of the “sleeve”.

We pay special attention to tap water. It is no secret that a lot of harmful chemical impurities enter the machine from the centralized water supply. They subsequently lead to the formation of scale, which in turn negatively affects the functioning of the washing machine. The problem is solved by installing special filters that soften and purify water.

It is not recommended to deal with scale with special means. Citric acid, vinegar, soda and store-bought cleaners often only worsen the situation. After using them, plaque can settle on the walls of the drain hose and on the heating element, and it is almost impossible to get rid of the renewed layer. It’s better to try to avoid problems and set up a filtration system right away.

When the water pressure decreases or voltage surges are detected in the electrical network, it is necessary to forcibly stop the cycle.Indesit reacts very sensitively to external negative factors, so it is better to “wait out” the failure and then continue washing. It is not necessary to unplug the machine: just press the “Wash Delay” or “Pause” button. Remember that modern machines can “remember” an interrupted program and even after 30 minutes they will start the drum from where it stopped.

Every year you should run a “cleaning” cycle: without laundry, with powder and at a temperature of 60-90 degrees.

We must not forget about comprehensive cleaning of the machine. At least once a year, it is recommended to thoroughly clean the machine: select the “hottest” program, add regular powder and run the cycle without laundry. Finally, you can turn on a single rinse to completely rinse the equipment. By following the recommendations listed above, you can extend the life of the machine by several years. The main thing is to be careful and remember to do it regularly.

Attention to some details

There are several other important points that do not directly relate to care, but greatly affect the operation of the machine. If you follow them, the machine will last longer and wash better. At the same time, the rules are simple and clear.

Place the machine on a hard and level surface. Ideally, concrete or tiles.
Check that water is supplied to the washing machine at the required pressure. The norms, lower and upper limits are specified in the technical data sheet of the model.
Make sure that the drain hose is connected correctly: with the “sleeve” raised 50-60 cm from the floor.
Sort laundry loaded into the drum by color and material.
Do not allow foreign objects (coins, keys, hairpins) to get into the drum by carefully turning out all pockets.
Do not wash old, torn or overly dirty items.
Fasten zippers and buttons and unhook decor from linen.
“Hide” woolen, downy items and clothes with metal inserts, spikes, rhinestones, and beads in a protective bag.

When connecting the Indesit washing machine to the electrical network, you cannot use extension cords and tees.

It is important to take the choice of detergent seriously. Preference should be given only to high-quality and easily soluble powders suitable for a specific washing regime. Be sure to select only mixtures and gels that are labeled “Automatic”. Do not add too much concentrate, otherwise soap deposits will remain on the internal parts of the machine.

It is not recommended to “drive” the washing machine too much. It is forbidden to run several high-temperature modes in a row without leaving a gap of 30-40 minutes between them. It is better to wash things at a minimum temperature without overloading the heating element. At the end of the program, disconnect the machine from the power supply and turn off the water.