Indesit washing machine is leaking

A leaking automatic machine is a very unpleasant breakdown. Firstly, the equipment will need to be repaired, which will be accompanied by some costs, and secondly, in this case, there is a high chance of flooding the neighbors below. Therefore, if your Indesit washing machine is leaking, you need to act quickly. It is necessary to find the “weak spot” of the unit as soon as possible and quickly eliminate the leak.

Why did this happen?

There are several factors that probably contribute to a leaking automatic washing machine. In some situations, even a combination of them can be observed. Most often the reason is as follows:

improper operation of the washing machine;
use of poor quality laundry detergents;
defects of individual parts or components of the machine, admitted at the factory;
damage to machine elements.

Before diagnosing the unit, you should empty the drum, turn off the power to the Indesit machine, and turn off the water supply. Next, you can begin to inspect the machine. Let's take a closer look at what can cause leakage and how to deal with the problem.

Let's check the external elements of the machine

The first step is to inspect the hoses of the washing machine, which leak quite often. They are in plain sight and are the easiest to reach. It is not difficult to find a defect (crack) on the surface of the drain or fill hose, and you can find the damage with the washing machine turned off.

It is recommended to wrap the hose with a paper towel or toilet paper; the place where the material becomes wet will indicate a defect causing a leak.

A leak may have occurred in the area where the hose connects to the MCA body. Then you need to disconnect the sleeve from the machine and replace the rubber gasket.If it turns out that the cause is a cracked hose, you should not try to seal it, as the leak will soon recur; it would be more advisable to immediately replace the element. hose is torn

We look at the powder receptacle

If after the next wash you find that there is water below, and on the left side of the machine body, inspect the detergent dispenser. Checking the cuvette is very simple - it is easy to remove from the body, the procedure does not take much time. The powder receptacle often leaks due to defects made by the manufacturer, as well as due to mechanical damage that occurs during cleaning of the tray, from falls or impacts. Things to remember:

have you recently dropped the powder container, for example, when cleaning it after another wash;
whether the cuvette was soaked in aggressive household chemicals;
did you rub the surface of the tray with a hard brush or try to scrape off the plaque with a sharp object?

If the answer to at least one question is “yes,” then remove the powder receptacle and carefully inspect it for cracks. Fill the tray sections with water and see if it flows out the bottom. If the powder compartment leaks, then there is nothing left to do but purchase and install a new dispenser. The powder tray may leak

Hatch rubber

If you see that a leak is leaking through the door, most likely the problem is in the sealing lip. In such a situation, water flows out from under the hatch and flows in a small stream along the front wall of the machine. It is necessary to carefully inspect the rubber band for damage.

Do not mistake the specially provided recess located in the lower part of the cuff for a defect.

You can try to repair the seal; if there are significant cuts, it is better to install a new rubber band.To prevent this type of damage, it is necessary to check the pockets of items before placing them in the drum. Coins, paper clips, hairpins and other items that can harm the gasket are often forgotten there. Minor cuff defects can be removed by using special patches and waterproof glue.

Internal pipes

If all the steps described above do not help eliminate the leak, you will have to dig deeper. Subsequent diagnosis involves partial disassembly of the MCA. Before starting work, do not forget to make sure that the washing machine is de-energized and disconnected from communications. It is necessary to provide free access to all walls of the case, so it is better to move the machine away from the wall.

First of all, you need to remove the top cover of the automatic machine by unscrewing the bolts that secure it. Then you will have access to the dispenser pipes. Next, you should check the pipes leading from the fill valve to the powder receptacle, and from the tray to the drum. Indesit pipe leaked

Another potentially dangerous place in terms of leaks is the connection point between the pump and the drain pipe. To check the connection, you will have to lay the Indesit washing machine on its side and inspect the elements through the bottom.

Main tank damaged

Tank defects often occur when not only clothes, but also shoes and belts are washed in the machine. Clothes with metal inserts, bra underwires, and other sharp and hard objects left in pockets can also damage the main container.

If a crack occurs in the tank, expensive repairs will be necessary with a complete replacement of the element.

It may not just be a defect. The tank is constructed from different parts fastened together. An integral part of the connection is the gasket.Over time, the elastic band loses its properties and begins to let water through. In this case, the sealing element will need to be replaced.

Destruction of bearings and oil seal

If the Indesit washing machine leaks during the spin cycle, you will have to change the seal. Over time, it wears out and begins to leak water. To inspect the seal, you will have to disassemble the SMA tank. During diagnostics, it may be revealed that the drum bearings also require replacement. rusty streaks on the back wall of the tank

There is another, easier way to check the oil seal and bearings. It is necessary to remove the back wall of the case (or just the technical hatch cover, it all depends on the Indesit SMA model). After this, you should carefully inspect the back surface of the tank. If rusty or oily smudges are visible on it, then we can absolutely talk about a seal defect.

Is it difficult to eliminate a leak?

Is it possible to fix a leak with your own hands, without resorting to the help of a specialist? If you carefully understand the problem and take a responsible approach to repairs, then of course yes. However, you should be extremely careful not to make the machine worse. If the washing machine is covered by a warranty, then you should not repair it at home; it is better to transfer the machine to a service center.

Actions taken will vary depending on the area where the leak is located. When water leaks from below, the sequence of manipulations will be as follows:

unplug the machine. Unplug the power cord from the outlet carefully, without touching the wet floor. If you cannot turn off the device from the network without stepping into a puddle, turn off the electrical power supply in the switchboard. It is important not to neglect this rule so as not to get an electric shock;
close the shut-off valve;
drain the water present in the drum.You can remove it by unscrewing the garbage filter located at the bottom, in the right corner of the Indesit washing machine;
unlock the drum door, remove the laundry;
find the location of the leak. If you find a defect in the hoses, replace them or repair the crack (by sealing it with a special rubber patch). If it turns out that the problem is a leaky gasket between the body and the hose, you need to remove the seal and install a new one. When the rubber band is replaced, the structure is assembled in the reverse order.

If the powder compartment is leaking, you will have to work with the dispenser. Remove the cuvette from the MCA and inspect its surface. If necessary, clean the tray from plaque, blockages, mold and mildew. Reinstall the cleaned dispenser and test the operation of the equipment. If the powder receptacle is cracked, you will have to replace it.

It is also recommended to check the water pressure and, if necessary, slightly close the shut-off valve to reduce the flow. If this doesn't help, the problem may be with the intake valve. It will probably need to be replaced.

A common reason for a washing machine to fail to seal is a defect in the hatch cuff. Open the drum door and inspect the seal. If cracks and cuts are found, you can “seal” them using waterproof glue and special patches. If you decide to repair the cuff, you will have to proceed as follows: the cuff will need to be replaced

loosen the clamps securing the seal;
rotate it so that the damaged area is located at the bottom of the hatch;
patch the defect;
return the elastic band to its previous position and secure the clamps.

If the cuff is severely damaged, it must be completely replaced.

When checking the solenoid valve pipe, remove the top panel of Indesit and inspect the element.If it has visible defects, it will need to be replaced. The intake valve pipe is a rather complex part; it is better to entrust its reinstallation to a specialist.

The filler pipe may also be leaking. You should remove it, process the seat, eliminate excess glue, and dry the joint area. Then the pipe is put back and fixed with high-quality waterproof glue.

If it is necessary to eliminate a leak resulting from a crack in the tank, then it will be problematic to cope with such work alone; you will need an assistant. First of all, you should tilt the automatic machine and inspect its bottom. In the case of vertical washers, the side wall is examined. The purpose of a visual inspection is to detect leaks. If wet spots are visible on the wall or bottom, then the reason, in almost one hundred percent of cases, is damage to the tank. It is impossible to repair it yourself without having the necessary knowledge and tools. Therefore, it is better to seek help from a specialist.

If the Indesit washing machine leaks during the spin cycle, the problem is due to failed bearings or a worn out oil seal. You will have to disassemble the machine, remove the tank, divide it in half, knock out the bearings, treat the landing area with a special lubricant, install new elements and reassemble the structure in the reverse order. This repair is classified as complex; it is better to entrust it to a competent specialist.

To prevent leaks from recurring

Careful operation is the key to successful work of the “home assistant”. The service life of individual parts and components of an automatic washing machine directly depends on how you use the equipment. To prevent unit leaks, it is recommended to follow simple rules:

items with metal inserts should be washed in special bags. Sharp and hard parts of clothing can damage not only the cuff, but also the drum and plastic tank. The same applies to small wardrobe items - they can be sucked into the drain pipe of the washing machine;
After finishing the wash cycle, be sure to unplug the machine. A voltage surge can cause the failure of any element of equipment, and, consequently, lead to a leak;
Do not exceed the maximum permissible drum loading weight. If you periodically overload the equipment, it will soon begin to leak during spinning;
if the tap water is too hard and dirty, install a filter device at the entrance to the apartment or washing machine. This will avoid the formation of scale on the elements of the washing machine, and will also prevent clogging of the input filters;
It is better to place the washing machine in rooms with less humidity, for example, in the hallway, corridor or kitchen;
Owners of “vertical” ovens should make sure that the drum door is tightly closed before closing the main lid. This will reduce the likelihood of leakage during spinning;
Do not use low-quality laundry detergents.

By following a number of simple recommendations, you can increase the maintenance-free service life of your washing equipment. If you take care of the machine, clean it, do not overload it, and use only high-quality household chemicals, the machine will not constantly leak.