Hans washing machine - error codes

Hansa washing machinesIn this post we will discuss the errors of washing machines from the manufacturer “Hansa”.

And also how they are displayed.

And so let's get straight to the topic.

 

Errors in PC models

Codes Causes of the malfunction and what happens nextWhy did the error occur?
E01Error with the designation E01. There is no notification that the UBL (washing machine hatch locking device) is turned on.Reasons that caused this malfunction:

  • The hatch is not locked.
  • There is damage to the wiring or loose contact from the lock to the controller.
  • The lock is broken.
E02Error E02 has occurred. Water filling into the washing machine is too slow or there is no filling.What caused the error?

  • Very low water pressure in the pipes.
  • The inlet hose is clogged or pinched. The pipes or other parts of the filling system are clogged.
  • The water tap may be turned off.
E03The display shows error E03 Water is draining from the washing machine tank too slowly. Or it doesn't merge at all.Why did the error appear?

  • The drain hose is kinked or clogged.
  • Clogged washing machine pipes.
  • The drain pump (pump) is faulty or clogged.
  • The drain pump filter is clogged.
E04An error code E04 has appeared. The level sensor informs that the washing machine tank is filled to the maximum with water.Why did the problem occur?

  • The fill valve is stuck open.
  • The level sensor (level relay) is broken.
  • During washing, the water pressure in the pipes suddenly increased significantly.
E05The message E05 appears: Filling the washing machine tank with water is too slow. Or lack of filling (filling takes more than 10 minutes).Let's look at the reasons:

  • The water supply hose is clogged or pinched.
  • Weak pressure in the water supply.
  • The level relay is broken.
  • The filling valve has become unusable.
  • The wires between the pressure switch and the fill valve could be damaged or the controller could be broken.
E06Error E06 has occurred. The water drains too slowly or does not drain at all (waiting for draining for more than 10 minutes).
  • The water drain hose is clogged.
  • The drain pump is stuck or has become unusable.
  • The level sensor has malfunctioned or its wires have deteriorated.
E07There is a leak. Water appeared in the tray of the washing machine. Aquastop activated.
  • The Aquastop sensor could have failed.
  • Or there was a water leak caused by a violation of the integrity of the tank or various pipes.
E08Violation of power supply parametersYou need to check the power settings.
E09Too much foam appeared in the washing machine during the spinning process.Most likely, too much detergent was used. Or a product not intended for machine washing was used.
E11The UBL simister does not work.The controller may have malfunctioned or broken down.
E21The washing machine motor is blocked. No response from the tachogenerator.
  • The electric motor or tachogenerator has failed.
  • There is no connection from the motor to the controller.
E22The engine runs even though it has not been given a command to run.The motor triac has probably shorted.
E31Temperature sensor shortedThere is a short circuit in the temperature sensor or its wiring.
E32The temperature sensor circuit is brokenThere has probably been a break in the integrity of the temperature sensor circuit.
E42The wash has finished, the washing machine door lock does not turn off. More than 3 minutes have passed.Such a malfunction can occur due to a broken hatch lock, door locking, or failure of the controller.
E52Energy malfunction machine memory.The malfunction occurred due to a data failure or a breakdown of the volatile circuit. memory controller (you need to change the controller or EEPROM circuit).

Errors in RA model machines

Code Causes of the malfunction and what happens nextWhy did the error occur?
E01UBL (hatch blocking device) does not work. After a couple of seconds, the inscription “E01” appears. The washing process stops.
  • The hatch lock is broken.
  • The integrity of the washing machine wiring has been compromised.
  • The controller has failed.
  • The voltage in the electrical network does not exceed 180 volts.
Limit switch does not function. After ten seconds, “E01” appears on the display. The wash stops.
  • The washing machine hatch is not locked or not fully locked.
  • Wiring fault.
  • The UBL has failed or the limit switch is turned off. castle
E02Three minutes after the command to fill the washing machine tank with water, there is no message that it has reached the required level. Seven minutes after the command to fill the washing machine, the washing process stops.
  • The water in the water pipe is turned off or its pressure is weak.
  • Controller failure.
  • The integrity of the wiring is broken.
  • The fill valve has failed.
  • Faulty level sensor (level switch).
E03Three minutes after the command was given to remove water from the washing machine, there was no message from the level sensor indicating that water had been removed from the tank. The UBL holds the hatch in the closed position until the machine is turned off.
  • Clogged drain hose or pipes.
  • Controller failure.
  • The level sensor has failed.
  • The filling pump has become unusable.
  • The wiring is broken.
E04The level sensor informs that the tank is filled to the maximum with water. The washing process stops. The drain pump starts. 2 minutes after all the water has been drained, the drain pump turns off. The hatch locking device holds the door in the closed position until the washing machine is turned off.
  • The controller may have failed.
  • During the washing process, the pressure in the water pipe suddenly increased significantly.
  • Hydrostat failure.
  • There is a defect in the filling valves.
  • Wiring faulty.
E05The temperature sensor has shorted or there is an open circuit. After a couple of seconds, a message will appear stating that an error has occurred. The wash will be completed until the end, but with cold water.
  • The temperature sensor is faulty.
  • Violation of wiring integrity.
  • Controller failure.
 -||- The water in the washing machine has heated by less than four degrees. An error appears on the display. Washing continues with cold water.
  • Heating element malfunction.
  • The mains voltage is too low (less than 180 volts).
  • The wiring is broken.
-||- The water in the machine did not heat up to the specified level within the time period set for this. An error is displayed. Nevertheless, the washing continues until the end.
  • Problems with the heating element (heating element).
  • Or low voltage in the electrical network.
E06Not applicable Not applicable
E07The tachogenerator does not indicate that the washing machine motor is running during the washing process. The engine restarts three times. If it does not work, the washing stops and error information appears on the display.
  • Failure of the tachogenerator (most often a coil break occurs).
  • The controller has failed.
  • The electric motor has broken down.
  • Wiring fault.
E08There is no message from the tachogenerator during spinning. Then the electric motor turns off. Then the engine restarts three times. If, despite this, it does not work, an error message appears.
  • The tachogenerator is broken.
  • The engine has failed.
  • Wiring fault.
  • Controller failure.
E09Not applicableAbsent

Hansa washing machine error codes

   

7 reader comments

  1. Gravatar Shahir Shahir:

    Tell me, what's the problem? Hans' machine displays p10 on the screen.

  2. Gravatar Anonymous Anonymous:

    How to remove error E01 on Hans Comfort?

  3. Gravatar Marina Marina:

    What does code p13 mean for the Hansa Fqua Spray 900 Comfort AA class washing machine?

  4. Gravatar Ilya Ilya:

    Tell me, what does error E35 mean? Isn't there one in the instructions?

  5. Gravatar Ivan Ivan:

    Tell me, Hans's machine is showing error E10.

  6. Gravatar Svetlana Svetlana:

    The spin stops at 0.08 and does not pick up any more speed, the time sensor shows everything at 0.08.

  7. Gravatar Evgeniy Eugene:

    Tell me error E74. It's Hans's machine, but there's nothing like that in the instructions.

Add a comment

We recommend reading

Washing machine error codes