How to remove the drum in an Atlant washing machine?

How to remove the drum in an Atlant washing machine To carry out certain types of repair work, it is sometimes necessary to remove the drum in the Atlant washing machine. This is a labor-intensive process and requires a lot of effort. However, if you strictly follow the instructions, even a beginner can handle the job. Let's figure out how to properly remove the assembly from the case, what tools should be on hand.

We collect everything you need

You need to prepare for repairs. First, you need to decide on a location. To easily disassemble the washing machine, you need enough free space. It is best to take the washing machine to a garage, workshop, shed, or at least move the machine from a cramped bathroom to a large room. The area where the machine is disassembled must be covered with dry rags, only then the device must be dragged there.

As for the set of tools, in the process of removing the drum you will need:

Phillips and slotted screwdrivers;
hammer;
bit;
set of keys;
WD-40 aerosol;
lubricant for washing machine elements.

Depending on the purpose of removing the drum, a repair kit is additionally prepared.

So, if you need to change the oil seal and bearings, you should first figure out which parts are available in Atlanta and purchase new spare parts from a specialized store. It is recommended to purchase original components. The repair kit will consist of bearings and an oil seal - a rubber seal that prevents water from entering the metal ring. When all the equipment for the upcoming repair of the washing machine has been prepared, you can begin disassembling the equipment.

Disassembling the top of the case

Before starting disassembly, it is necessary to turn off the power to the washing machine and disconnect it from the house communications. Be sure to drain any remaining water from the system through a garbage filter. The further algorithm of actions will be as follows: dismantling the top of the Atlant machine

pressing the central latch, remove the powder receptacle from the machine;
unscrew the bolts securing the unit cover;
remove the top panel;
Unscrew the four screws on the transverse metal strip;
Using a Torx wrench, twist the counterweight lock and remove it from the housing;
unscrew the fasteners of the “hopper” for detergents, unfasten the pipe from it, take out the dispenser;
disconnect the pipe from the tank, first loosening the fixing clamp.

So, the upper part of the tank will be “cleaned” of various parts and elements. The next disassembly step is to release the rear wall of the assembly. Let's see what to do next.

Let's open the technical hatch

Now you have to work on the back of the Atlant washing machine. It is necessary to remove the back wall of the machine. This will provide access to the pulley, drive belt, motor and other elements that require dismantling. The instructions for action are as follows:

Unscrew the bolts around the perimeter of the rear panel and dismantle it;
remove the belt from the drum “wheel”;
disconnect the wires from the heating element;
disconnect the motor wiring, tighten the bolts and pull the engine out;
loosen the drain pipe clamp, disconnect the hose from the tank;
disconnect all wiring attached to the tank-drum assembly;
Unscrew the bolt securing the pulley and remove the drum “wheel”.

If the center pulley bolt does not budge, spray it with WD-40.

Next, all that remains is to remove the shock-absorbing spring mounts.This way, there will be nothing above or behind to prevent the drum from being removed. All that remains to be done is to work on the front wall of the washer.

Front side of the case

The cuff of the hatch door and the front panel of the housing will interfere with removing the drum. You will have to dismantle the front wall and perform a couple more steps. The algorithm will be as follows:

open the machine door;
fold down the outer edge of the cuff;
Use a slotted screwdriver to loosen the metal clamp securing the rubber band;
place the sealant inside the drum;
remove the bolts located around the perimeter of the front wall of the unit;
Unscrew the screws securing the UBL;
lift the panel up and carefully set it aside.

After dismantling all the “interfering” elements, you can remove the unit from the Atlant washing machine body. Lift the tank (this will help remove it from the hooks) and place it on a flat surface. After this, you can directly repair the machine - disassemble the drum and replace the bearings, or throw out the old one and install a new unit. The machine is assembled in the reverse order. To avoid confusion when connecting parts of the unit, it is recommended to photograph each disassembly step.