Zanussi washing machine does not rinse

Zanussi washing machine does not rinse Sometimes users approach a Zanussi washing machine and see that it is stuck at the rinsing stage. The displays of modern machines display an error code corresponding to the malfunction. What to do in this case - because things remain locked in a drum full of water?

Let's figure out why the Zanussi washing machine most often does not rinse. Let us explain which parts of the washing machine to check first. We'll tell you how to act in this situation.

Problem outside the CM housing

If the washer cannot start rinsing, it freezes towards the end of the cycle. The tank remains full of soapy water. It is unrealistic to ignore this situation - you will have to diagnose the machine and check the operation of the main elements.

Whenever possible, it is better to delegate the diagnosis and repair of a Zanussi washing machine to specialists. If not, it’s quite possible to deal with most problems yourself. We'll tell you where to start checking the machine.

Make sure there is nothing obstructing the drainage of waste water from the tank.

Most often, Zanussi machines do not start rinsing clothes due to problems with drainage. Diagnosis should start with the simplest things. Inspect the drainage hose - it may be pinched or crushed, and therefore the water does not go down the drain. drain hose clogged

If the corrugation has nothing to do with it, you will have to check if there is a blockage in the sewer pipe or siphon. You can talk about a clogged common riser when water also does not drain well from the toilet or washbasin. In this case, you will need the help of a plumber.

When the machine does not start rinsing and the tank is empty, you can check if there is water in the tap. Perhaps the supply has been turned off and the washer simply cannot fill.

After making sure that external factors do not prevent the machine from starting rinsing, you should look for the reason inside the machine itself. Diagnostics are performed from simple to more complex. We'll tell you what can cause the SMA to freeze at this stage.

Most likely breakdowns

Don't panic if you see your Zanussi automatic machine stuck in the rinsing phase. In most cases, this is caused by a minor problem. Most often, the washing machine does not rinse or spin clothes due to a clog in the drain system. You can deal with this problem yourself without calling a specialist.

A failed drain pump, a broken pressure switch, or a damaged control module can also lead to freezing during the rinsing stage. We will tell you how the breakdown of these elements affects the performance of the machine.

Clogged drainage system elements. The drain hose of the machine, the garbage filter, the pump, or the pipe that connects the tank and the pump can become clogged. A coin forgotten in a pocket can get stuck inside the washer and become an obstacle to the normal outflow of liquid. When the water drainage is blocked, the machine freezes without starting to rinse. The solution to the problem is to clean the nodes.
Faulty drain pump. The pump is responsible for pumping water out of the washing machine tank. If the element breaks, the liquid remains inside and the machine cannot proceed to the next stage of the cycle.
Pressostat. A level sensor that is not functioning correctly transmits unreliable information to the control module.For example, it reports that the tank is empty, but in fact it is full. As a result of this, the “brain” does not activate the drain, and the machine does not start rinsing, but freezes.
Control module. Rarely, the culprit behind Zanussi SMA freezing is a damaged board. The electronic unit coordinates all processes, so if it breaks down, the washing machine starts to work incorrectly.

First, the washing machine is checked for blockages. Then the pump and pressure switch are inspected. If the cause of the freeze is not identified, the electronic module is finally diagnosed.

Hose or "trash can"

If you find a washing machine frozen during the rinsing stage, you first need to empty the machine. You can remove soapy water through the drain filter - this way you can also check the “trash bin”. The algorithm of actions will be as follows:

turn off the power to the Zanussi automatic machine;
turn off the valve responsible for supplying water to the washing machine;
move the washing machine a little away from the wall;
find the garbage filter (it is located in the front, in the lower corner behind the false panel or technical hatch);
place a dry cloth near the machine;
place a low container under the washing machine at the location of the “trash bin” (it will be needed to collect water);
unscrew the filter halfway;
wait until the water drains into the basin;
remove the trash can completely.

When you drain the water from the tank, the lock will unlock so you can open the door and remove the laundry. After this, clean the drain filter. You can wash the “trash can” only in warm water - when exposed to too high a temperature, the plastic is deformed.

If there are lime deposits on the filter element, you can remove them using citric acid. Soak the “trash can” for 2-3 hours in the “lemon” solution.After this, the filter is washed under running warm water.

It is recommended to clean the drain filter of an automatic machine at least once every 2-3 months.

Next, look into the hole from which the drain filter was removed. If there are any foreign objects there: paper, coins, buttons, take them out. Next, remove dirt from the walls with a damp cloth.

Also inspect the drain hose - feel it along its entire length. Perhaps there will be a blockage in it. Having found the “lump”, disconnect the sleeve from the machine and siphon and rinse under running water. You will probably have to clean the corrugation with metal wire.

The pump has failed

Usually, the drain pump does not fail suddenly - the “symptoms” of its malfunction appear in advance. If you noted that the machine took too long and noisy to pump out water before, then it is quite possible to “sin” on the pump. The element may stop working properly due to:

blockage;
breakdowns.

If the problem is clogged, the pump should be cleaned. You can get to the pump through the bottom of the washing machine. The algorithm of actions is as follows:

de-energize the SMA, disconnect the device from communications;
lay the washing machine on its side;
remove the tray (if provided);
find the pump;
loosen the fasteners and remove the pump from the machine body.

Inspect the item. It is possible that debris has accumulated in the impeller - then you need to clean the blades. If there is no visual damage, check the pump with a multimeter (to do this, you need to attach the tester probes to its contacts and measure the resistance value). A burnt out drain pump cannot be repaired - the part will need to be replaced.

When buying replacement parts, be guided by the model and serial number of the Zanussi machine. You can also take the dismantled pump with you to the store and ask the consultant to select a similar part.This way you won’t make a mistake when selecting components.

It's all about the electronic module

Very rarely, Zanussi washing machines freeze during the rinse phase due to an incorrectly functioning control module. Sometimes the integrity of the wires is compromised, and in some cases the semiconductors on the board break down. To identify the problem, a thorough diagnosis of the circuit will be required. control module from Zanussi

It is better to entrust the repair of the SMA control unit to specialists. Without sufficient experience and knowledge, you can only harm the “home assistant” even more. A competent technician will diagnose the board and solve the problem.