The Indesit washing machine constantly fills with water

An alarm bell indicating a breakdown of the washing machine is the continuous intake of water into the system. In such a situation, after starting the program, the machine only fills, but the washing does not start. It will not be possible to turn a blind eye to this behavior of the “home assistant”; urgent action must be taken. Let's figure out what to do if the washing machine constantly fills with water. What is the probable cause of this malfunction?

“Symptoms” of a breakdown

As a standard, during the washing process, the automatic machine fills and drains water several times (usually 2-3). It is difficult not to notice that liquid enters the system continuously. The main “symptoms” noted by users in this situation:

• the incessant noise of water being collected;
• extended washing program. Since the process is not carried out correctly, the cycle time increases;
• At the end of washing, the clothes are still dirty, with soap smudges. This is observed because the required concentration of the soap solution is not achieved.

It is worth eliminating the reason for the machine’s constant intake of water immediately after identifying the problem.

It is dangerous to operate the washing machine with such a violation. This can lead to complete equipment failure.

What could have gone wrong?

Various factors can cause the Indesit machine to constantly fill with water. Initially, you should identify all possible problems, and during the diagnostic process, narrow down the range of breakdowns. So, what can cause a continuous supply of liquid from the water supply:

• incorrect connection of the washing machine;
• damaged washing machine tank;
• broken pressure switch;
• broken intake solenoid valve;
• faulty control module.

If only the purchased machine showed a problem in the first wash, it is not necessary that it was connected incorrectly. Perhaps there is a normal manufacturing defect. In this case, it is better not to carry out repairs yourself, but to submit the equipment for warranty service to a service center.

Let's check the drain hose

Diagnostics of the Indesit washing machine should be carried out from simple to complex. First of all, it is recommended to check the connection of the machine. Most often washing machines Indesit keeps drawing water due to an incorrectly connected drain hose.

The equipment always comes with instructions that describe in detail the process of connecting the machine to house utilities. The main rule is that the drain hose must be positioned at a height of 50-60 cm from the floor. If you extend the hose lower, the water will be removed by gravity into the pipe, the pressure switch will send a signal about the empty tank to the “brain”, and the control center will give the command to fill the system with water again. And so on in a circle.

You can check if this is the reason visually - just inspect the sleeve and make sure that it is at a sufficient height. If inspection is not possible, it is possible to evaluate the position of the hose in another way:

• turn on any washing program;
• wait until the tank is full;
• start the “Drain” mode;
• In the middle of the descent, press the "Pause" button.

If the liquid continues to leave the system even when the process is paused, then the problem is definitely in the drain hose. If the water level remains the same, you will have to look for the problem further.

By the way, often the equipment comes with a special loop designed to secure the drain hose.The hose is inserted into the plastic element, thus securing it in the correct position.

Problems with the fill valve

In some cases, the continuous intake of water is explained by a failed inlet valve. When the sensor is faulty, fluid enters the system constantly. So, when the wash starts, the “brain” gives a command to fill the tank. A broken valve cannot stop drawing water. The protective system is activated, and if there is an excess of liquid, it begins to drain it. The process happens in a circle. What should the housewife do in this case?

Please note:

• on the tank filling rate. If the water comes in slowly, the valve membrane is probably damaged;
• Filling too quickly indicates a breakdown of the electromagnetic element itself.

The intake valve cannot be repaired; you will have to buy and install a new part.

The sequence of actions when dismantling and subsequent installation of the element will be as follows:

• turn off the power to washing equipment;
• remove the top cover from front-loading machines, or the side cover from machines with a vertical loading type;
• find the fill valve, disconnect all wiring and pipes from it;
• unscrew the bolts holding the valve or loosen the fixing latches (depending on the type of fastening of the element on your washing machine model);
• remove do;
• put the new valve in place, tighten the bolts (or secure it with latches), connect the pipes and wires;
• assemble the washer body;
• run a test wash.

Changing the valve is not difficult; this work can be done at home. The main thing is to select a replacement part that is similar to the one being dismantled.

The level sensor is acting up

The pressure switch controls the volume of water in the system.When the tank is filled to the required level, the sensor transmits a signal to the control module, and the “brain” sends a command to stop collecting liquid. If the pressure switch fails, the control unit does not receive correct information about the amount of liquid in the tank. As a result, the normal washing cycle is disrupted. The level sensor stops functioning correctly for various reasons:

• oxidation of its connectors and contacts;
• short circuit of the pressure switch wiring;
• loss of membrane tightness;
• clogged or defective pressure pipe.

To begin with, you can try to repair the sensor - clean oxidized contacts, weld defects, clear blockages. If this does not give results, you will have to buy and install a working pressure switch. The algorithm of actions will be as follows:

• remove the “top” of the machine body by unscrewing the bolts holding the cover;
• disconnect the pressure tube from the level sensor;
• disconnect the chip with the wiring;
• remove the pressure switch by releasing the latch that secures it;
• install a working element;
• make the connection in the reverse order (chip, tube);
• Secure the top cover of the washer in place.

When repairing an automatic machine, be sure to follow the safety rules - disconnect the equipment from the network and close the shut-off valve.

In such a situation, it is also very important to select a part similar to the one removed. Find out the exact name of the “home assistant” model and then purchase a replacement part.

Damage to the main tank

A crack in the tank of an Indesit washing machine is far from uncommon. Finding out about a hole is easy - water will accumulate under the washer during washing.This breakdown is very dangerous, as it can cause a flood in the apartment, causing damage not only to your home, but also to your neighbor’s.

The most dangerous cracks appear at the bottom of the tank. Holes in the upper part are not so bad, because in this case the water will not flow onto the floor - most Indesit programs provide for only half filling the drum with water. To inspect the bottom of the tank:

• Turn off the power to the washing machine, disconnect the inlet and drain hoses from the communication terminals;
• drain the water from the tank (through a garbage filter or drain hose);
• move the machine to the middle of the room (the ideal place for repairs would be the garage);
• place the washing machine on its right side;
• inspect the bottom of the tank. You can use a marker to mark suspicious places that look like holes.

It is ideal to replace a leaking SMA tank with a new one. However, if the defect is not too large, you can try to restore the integrity of the element with a high-temperature, waterproof sealant or cold welding. You can take the equipment to a workshop and ask a specialist to solder the tank. However, you should understand that it will be difficult to obtain a warranty for such repairs.

Looking at electronics

If all the previously listed reasons for the continuous supply of water into the tank are excluded, you will have to check the control module of the Indesit washing machine. The electronic unit controls the entire process, receives signals from various sensors during washing and transmits further instructions on the operation of the machine. If the control board fails, the washing machine will not be able to function properly, and the operation of the machine components will be disrupted. The main reasons why the control module is damaged:

• voltage drops in the network;
• exposure to moisture on the board;
• mechanical defect;
• natural wear and tear of the block.

If the problem lies in the “brain of the washing machine,” then it is better not to start repairs at home. Working with electronics requires certain knowledge and experience. In order not to aggravate the situation, it is recommended to seek help from a specialist.

The sooner after identifying a problem you begin to eliminate the cause, the fewer “sacrifices” you will be able to make. Postponing repairs will lead to much more serious damage to the SMA.

Reader comments

• Share your opinion - leave a comment