Ardo washing machine does not fill with water

Ardo washing machine does not fill with water It is very easy to guess that the washing machine is not taking in water: just open the powder receptacle slightly and look at the powder. If the machine hums, but it remains dry, it means that the water supply is interrupted. Several failures at once can lead to problems with the fill, from a banal blockage to the failure of an expensive control board. You can deal with the problematic set yourself. Step-by-step instructions and recommendations from the manufacturer will help you with the repair.

Let's study typical problems

The washing machine stops filling for many reasons. The most obvious of them are turning off the central water supply or turning off the tap on the pipe, and the most expensive thing is to repair a broken control board. But there are also typical problems that most often lead to a “dry” machine. As a rule, these are problems with the inlet valve, filter, pressure switch, pump and electronic module.

The inlet valve is broken. This part is “responsible” for supplying water to the machine - after starting the program, the valve membrane is activated, the mechanism opens, and filling begins. In the event of a breakdown, the algorithm is disrupted, since the “door” remains closed. To check the functionality of the device, you need to apply a voltage of 220V to it. A working device will close and a click will be heard, while a non-working device will remain silent. In the latter case, replacement of the valve is indicated; it cannot be repaired.
The inlet filter is clogged. For safety reasons, the machine filters the water entering the tank, preventing impurities and dirt from getting inside. It is logical that the bulk of the retained debris remains on the filter mesh, impeding the water flow.The washing machine is trying to fill, buzzing, but nothing happens - the hose is clogged.

Typical breakdowns that lead to the impossibility of dialing on Ardo are problems with the pressure switch, inlet valve, filter, board and pump.

The pressure switch has failed. The level sensor must transmit information about the degree of filling of the tank to the control board, but if it malfunctions, its operation is not accurate enough. For example, it can signal that there is enough water even when the drum is completely empty. The module will respond by stopping dialing, leaving the machine “dry”. There is only one way out - to check the serviceability of the pressure switch: disconnect the tube from the body, blow into it and listen. The sound of clicks will indicate the operability of the device, their absence will indicate a breakdown.
The control board has burned out. Perhaps the problem is in the “brain” - due to damaged triacs or “tracks”, the module cannot process information and give a command to fill. It is necessary to carry out a comprehensive diagnosis of the unit, calling each element of the system. By the way, checking and repairing electronics on Ardo is a rather risky and time-consuming task. It is better to entrust this matter to the service center specialists.
The pump failed. Before each cycle, the machine pumps out the water remaining at the bottom of the tank - this way the functionality of the pump is checked. If during the auto-check it turns out that the drain is not working, the board disconnects for safety reasons, and the program ends before it even begins.

The list of typical causes is often supplemented by rare failures. So, sometimes the washing machine does not fill due to a damaged wire connecting the pressure switch to the tank. In some cases, the fault is in the hatch blocking device: the UBL does not work due to a loose door, and the machine cancels filling the water.

Let's eliminate trivial problems

There is no need to panic - perhaps the washing machine does not fill with water due to the user’s carelessness. First of all, we check whether there is a central water supply, whether there is sufficient pressure and whether the tap on the pipe is open. Be sure to pay attention to the hatch door; it must fit tightly to the body, otherwise the UBL will not work and the water intake will not begin. If there are no external problems, we proceed to diagnosing the machine. The main elements of the filling system are checked in sequence from easy to complex. So, the first in line are the inlet valve and filters, and the last ones are the pump and control board.

Before any repair operations, it is necessary to turn off the power to Ardo and disconnect it from the water supply.

First we deal with the inlet hose, especially if the machine makes an uncharacteristic buzz when trying to draw water. It is enough to loosen the clamp and disconnect the hose from the equipment, and then inspect, straighten and rinse under the tap. If cleaning the hose does not help, move towards the inlet filter. This is a fine mesh that often becomes clogged with plaque and dirt, preventing water from entering the machine. You can check its status like this: intake valve screen is clogged

unhook the hose from the Ardo body;
find the mesh installed next to the valve;
grab the protruding part of the mesh with pliers;
pull the filter towards you (no need to unscrew);
clean the mesh, if necessary, soak in lemon solution;
return the filter to its seat.

You should immediately check the coarse filter - it is built into the water pipe and located behind the tap. This nozzle is responsible for the primary filtration of water, so the lion’s share of impurities and debris settles on it.To wash it, you need to fix the joint with one wrench, and with the second, unscrew the nut holding the flywheel. Be sure to place a basin next to it, since when the fasteners are unscrewed, the stream will pour onto the floor. There is no need to remove the mesh - a powerful stream will remove all dirt. The main thing is to return everything to its place.

Filling system and heating element

As practice shows, Ardo washing machines, like other modern machines, do not draw water well due to problems with the inlet valve. These devices cannot be repaired, and in case of any breakdowns they are simply replaced with new ones. The replacement procedure is quite simple, so even a “newbie” can handle the job. To replace the valve you must:

check that the washing machine is disconnected from communications;
remove the top cover (what to do for this depends on the machine model: usually you need to unscrew the fixing bolts from the rear panel and move the “top” back, lifting it up);
unhook the drain hose from the machine body (the water remaining in the hose must be drained);
find the inlet valve;
take a photograph of the wiring connected to the valve and disconnect the contacts;
turn off the supplied pipes (remember that water remains in them);
loosen the bolt holding the device;
remove the valve;
install a new valve in the grooves, secure it with a screw;
Based on the photo taken, connect the wiring and pipes;
return the cover to the Ardo body;
fix the inlet hose;
connect the washing machine to communications;
run a test cycle and check if the flooding has improved.

When looking for replacement parts, you need to rely on the serial number of your existing Ardo washing machine.

Typical breakdowns of the Ardo filling system include problems with the heating element.As a rule, we are talking about a thick layer of scale, due to which the device overheats and fails. It is necessary to dismantle the heater, test the multimeter, and if it malfunctions, replace it with a new one. The sequence is:

remove the top cover;
disconnect the back panel from the case;
tighten the drive belt;
find a heating element - a metal strip under the tank with many connected wires;
take a photo of the “chip” to facilitate reverse connection;
unhook the connected wiring;
unscrew the bolt on the heating element;
After rocking, remove the heater.

We test the removed heater with a multimeter. If a malfunction is detected, then repair will not help - only replacement. The instructions on what to do are as follows:

treat the seal on the heating element with dish gel;
place the heater in the seat;
secure the device with a nut;
connect the wiring, thermistor.

If everything is in order with the heating element, then there is another option - problems with electronic locking. It is possible that the UBL has failed and does not operate even with the door tightly closed. To check the device, you need to disconnect Ardo from communications and pay attention to the hatch door. You will have to test the blocker with a multimeter, and if it malfunctions, repair or replace it. It is not difficult to figure out why the Ardo washing machine does not fill with water. The main thing is to act consistently, remember safety precautions, and if serious problems are detected, contact specialists.