First launch of Weissgauff dishwasher

First launch of Weissgauff dishwasher Usually, after purchasing new equipment, people are impatient to start the Weissgauff dishwasher for the first time, forgetting about the instructions and any precautions. You definitely shouldn’t do this, because if you don’t follow certain rules, you can even damage the equipment you just purchased. Let's look in detail at how to properly start using a Weissgauff brand dishwasher.

Commissioning of the PMM according to the instructions

It is best to start the device for the first time strictly according to the manufacturer’s official instructions, so as not to miss all the most important nuances, starting from the initial connection of the equipment to all communications, ending with the procedure for installing dirty dishes in the baskets of the washing chamber. This is also important because not only do different brands have different operating instructions, but even each individual model.

The initial connection to the water supply should be left to the service center specialist if you do not have the necessary experience in connecting the machine to all communications.

The first switching on of the PMM must be idle, that is, without dirty dishes and other unnecessary items. This operation is necessary due to the fact that during the assembly of equipment at the factory, factory dirt, oil, and dust may remain in the device if the unit has been stored in a warehouse for a long time. To eliminate all these impurities, an idle start is necessary, during which there should be no dishes inside, so as not to contaminate them and not interfere with cleaning the machine. In addition, the test is a good opportunity to check the performance of the “home assistant”:

Is tap water flowing normally into the washing chamber?
is the operation of the machine interrupted during washing;
is water leaking anywhere during the operating cycle;
does the heating element heat the water in the machine to the selected temperature;
The liquid inside the device circulates uninterruptedly, and then completely goes down the drain.

These five points are very important for the normal operation of the PMM, which is why it is so important to start the machine correctly for the first time and monitor the listed parameters. For the test you will need to perform a number of simple steps.

Add salt, regenerating ion exchange resin and detergent to the equipment.

Salt and household chemicals should be intended exclusively for dishwashers, so as not to damage the internal components of the equipment during operation.

Unlock the shut-off valve that supplies water to the machine.
Connect the device to the power supply.
Turn it on with the “Power” button.

Select the longest working cycle, which is usually an intensive wash program.
Make sure that the door of the household appliance closes until it clicks.
Activate the wash with the “Start” key.

Only after making sure that the idle start was successful can you load the baskets with dirty dishes and start a full work cycle. You should select a program in accordance with the degree of soiling of the dishes, as well as paying attention to the type of cutlery. For example, it is better to wash lightly soiled cutlery in the quick wash mode, and complex stains, pans with ingrained fat and burnt food - in the intensive mode. put dishes in baskets

A very convenient function on modern Weissgauff machines is changing the specified cycle if it was selected incorrectly.This can only be done until the equipment has started using detergent, otherwise it will no longer be possible to change the cycle. To make the adjustment you need:

open the washing chamber door;
hold down the key for the selected washing mode for a few seconds to cancel it;
activate the correct program;
close the PMM door.

If you simply open the door during the working process, the device will stop washing for a while, but 10 seconds after closing the door it will simply continue working. This can be used to additionally load forgotten dirty dishes. As in the case of changing the operating mode, this can only be done while the household chemical dispenser is closed. To do this, follow similar instructions.

Open the dishwasher door and wait until operation stops.
Carefully add extra dirty dishes.
Close the door and wait for work to begin.

As soon as the washing is completed, the equipment will notify the user about this with a special sound signal. After this, just turn off the equipment, open the washing chamber door and wait a few minutes so that the dishes have time to cool down.

Substances for the first activation of PMM

For smooth operation of the dishwasher, special household chemicals are required, such as PMM salt, detergent and rinse aid. In addition, once a quarter it is necessary to additionally purchase a special cleaner.

Salt must be in the device so that the ion exchanger can soften hard, low-quality tap water. To do this, before the first start, you need not only to load salt granules into the device, but also to adjust the hardness of the water with which the softening element will have to “fight”. For all this you need: water hardness table

find the salt bin at the bottom of the washing chamber;
unscrew the lid of the salt compartment;
find a ring with an arrow on the tank;
set the required hardness values of the ion exchanger;

You can find out the level of water hardness using special test strips, or by contacting the official website of the city water utility, which is obliged to regularly provide correct information about water quality.

fill the hopper with water to about two-thirds of the total volume;
load approximately 1 kilogram of special salt into the department, for convenience using the funnel from the PMM starter kit;
Close the reservoir lid tightly.

Water is poured into the salt bunker only once, and salt must be added depending on consumption - in some settlements you will have to do this once a month, and in some - once a year. The machine itself will report this using a separate indicator on the control panel of the device. However, everything described does not apply to a water supply system with high-quality soft water, because in this case regenerating salt is not needed at all.

The rinse aid in the “home assistant” helps eliminate stains and unpleasant deposits from dishes, and also allows the dishes to dry faster. The user does not need to think about its consumption, because the product is added during operation in automatic mode at the very end of the wash. It is enough just to select the desired chemical consumption by setting the lever to the desired position and add the product to a special reservoir located on the door of the washing chamber. It holds only up to 140 milliliters of liquid, so it is worth filling it completely before turning it on for the first time, and then replenishing the compartment from time to time.

Finally, with detergents, housewives have a wide choice, because this chemical is available in several variations - from tablets and capsules, to powder and liquid gel. This type of household chemicals is used to effectively remove all types of contaminants from dishes and, like rinse aid, must be loaded into a special dispenser located on the PMM door. If you use powder, then pay attention to the special mark indicating the minimum dose of detergent, which is usually 20 grams. When using tablets and capsules, everything is much easier - you only need to load one piece per working program.

Don't neglect caring for your equipment

Proper switching on of equipment is only the first step to ensure that the equipment lasts a long time. It still needs to be looked after promptly and properly. This list includes not only using the cleaner once every few months, but also constantly cleaning internal and external surfaces, removing food residues and other debris behind the rubber seals of the washing chamber, cleaning filters and much more.

Be sure to leave the dishwasher door open for several hours after the end of the cycle so that the machine is ventilated and does not develop mold with an unpleasant odor.

It is also worth highlighting the treatment of sprayers that spray water inside the device, cleaning dirty dishes with powerful jets of water. If you do not take care of the nozzle brackets, their nozzles and bearings may become clogged. How to avoid this? dishwasher care

Unscrew the nut.
Remove the washer that is installed on top of the bracket.
Remove the spray arm itself.
Clean the bracket using a brush and hot soapy water.
Reinstall the parts.

In conclusion, we note the importance of using a cleaner - a special type of cleaning chemical that helps clean the inside of the dishwasher. It must be purchased approximately once a quarter in order to get rid of complex contaminants inside the most inaccessible areas of equipment.