Whirlpool washing machine errors without display

Whirlpool washing machine errors without display Whirlpool automatic machines can notify the user of breakdowns in two ways. Washing machines equipped with a display display the corresponding error code on the screen. In this case, it is easy to understand what failure occurred in the system - just decipher the designation using the instructions.

Machines that do not have a display indicate a problem by lighting indicators on the control panel. Here you will have to observe what lights are on and come to the conclusion which element of the machine has failed. Let's figure out how to decipher errors on Whirlpool washing machines without a display.

Let's deal with light bulbs

The LEDs on the control panel of older Whirlpool models are located above the program switch knob. You need to count the light bulbs from left to right. So, the first indicator will be “No water supply”, the second will be “Pre-wash”, the third will be “Wash”, the fourth will be “Rinse”, the fifth will be “Water Hold”, the sixth will be “Drain/Spin”, the seventh will be “Door Open”. As for the lower ones, the eighth is considered the “Clean filter” diode, the ninth is “Service”.

bulb numbers

It is through the blinking of some of these nine lights that the technology indicates a failure that has occurred in the system. It is necessary to count which LEDs are lit and figure out what kind of malfunction is indicated by a Whirlpool washing machine without a display.

Basic codes

If your Whirlpool washing machine suddenly stops working, be sure to pay attention to the dashboard. Using LEDs, the machine will indicate the error code and significantly narrow the range of possible problems. To restore the unit, you will have to figure out what failure occurred in the system and carry out the repair yourself or with the help of a technician.

You need to count the light bulbs from left to right, and very carefully so as not to confuse the serial number of the LED.

Let's look at the main fault codes for Whirlpool washing machines and the LEDs corresponding to each error.

F LEDs 4 and 9 light up (Rinse and Service lights). Indicates a malfunction in the heating system. If within the allotted time the water in the tank does not reach the set temperature, the machine generates this error. To eliminate the breakdown, you will need to diagnose the circuit of elements, maintain the contacts or replace the wiring.
F Lamps 4, 6 and 9 are lit. The washing machine indicates a faulty temperature sensor. You should find out the resistance of the thermostat using a multimeter, and if necessary, replace the part.
F Glow of 4, 5 and 9 diodes. Intelligence cannot receive signals from the tachometer. This error will be accompanied by the motor rotating at slow speeds. Most often the problem is in the Hall sensor. Sometimes it is enough to simply return the washer that has fallen off to its place; in some cases, the element needs to be replaced. It is extremely rare that F06 indicates a breakdown in communication in the tachometer – engine – module circuit.
F The fourth, fifth, sixth and ninth indicator lights up. Reports violations in the motor control circuit. You'll have to check the main module. The triac responsible for the operation of the motor may be damaged, then replacing the semiconductor element will help. The second option is that the entire board is faulty and needs to be reinstalled.

If repairs to the main control unit are required, it is better to contact specialists so as not to damage the equipment even more.

F The third and ninth display lights up. The Whirlpool machine informs about the failure of the heating element. The heater does not always break; sometimes it is due to a break in its wiring or oxidation of the contacts. The thermostat circuit may be broken - so check the sensor and wiring. In addition, error F08 may indicate a faulty pressure switch or damage to the control board. This will require further diagnostics of the equipment.
F The machine has detected too much water in the tank. “Overflow” can be caused by a broken pressure sensor, a faulty inlet valve, or a malfunction of the main electronic module. Depending on its cause, replacing the pressure switch, fill valve or repairing the control board will help solve the problem.
F Engine malfunction. The engine, with this error, generally stops working due to damage to the temperature sensor or failure of the triac. If you cannot repair the components, you will need to completely replace the electric motor or control board of the washing machine. Whirlpool.
F The machine informs about the problem “from the outside”. Code F11 indicates insufficient voltage in the network. If the parameters do not meet the standards, it is better to contact an electrician.
F The third, fourth and ninth diodes light up. The machine informs that the wash is carried out in cold water, it does not warm up to the specified degree. There may be several reasons for the malfunction. The first is the sticking of the relay that controls the heating. This component of the control board will need to be replaced. The second is that the heating element has burned out or there is a breakdown on its body. The problem is solved by replacing the tubular element. The third is a break in the wires connecting the heater and the processor, then maintenance of the contacts is necessary.The fourth is a breakdown of the temperature sensor.
F Indicators 3, 4, 6 and 9 are lit. The machine cannot fill - water either does not fill or enters the tank very slowly. This error may appear if there is insufficient pressure in the house communications, a clogged powder receiver, a dirty inlet filter, or a clogged inlet valve. You will need to wait until the liquid supply situation improves, or clean the detergent cuvette or mesh filter.
F LEDs 3, 4, 5 and 9 light up. Informs about processor failure. To solve the problem, you will have to reflash the microcontroller or replace the entire module.
F The glow of 3, 4, 5, 6 and 9 bulbs is observed. In Whirlpool washing machines, this error means motor failure. It will probably be necessary to replace the converter brushes and install a new tachometer. Perhaps the issue is a violation of the “message” between the engine and the control module. Sometimes repair or replacement of the electronic unit is necessary.
F The machine signals a fault in the control system. It can help to correct the situation either by checking and restoring the contacts, or by repairing individual sections of the board, or by completely replacing the command unit.
F The unit usually freezes during the cycle. Sometimes the equipment refuses to turn on at all. The code indicates problems with the power supply system. Probable causes: insufficient voltage in the home network, defective cord, damaged plug, broken socket, faulty washing machine power filter.
F Indicates a malfunction of the control board. In most cases, restarting the washing equipment helps correct the situation. If you cannot reset the error code, you will need to diagnose the electronic module and possibly repair or replace it.
F Indicators 2, 4, 6 and 9 light up.The machine does not start due to the control module refusing to work. Most likely, the “processor-dashboard” circuit has broken. You will need to check the contacts and wires. Sometimes repair or replacement of the controller is necessary.
F This error code may indicate two completely different failures at once. The first is a malfunction in the operation of the heating element. The second is the inability to draw water due to a clogged powder receptacle. If the problem is in the tubular heater, you will have to replace the element or adjust the wiring between it and the control board. If it is in the detergent cuvette, a simple cleaning of the tray will help.

To clean the powder tray, remove it by pressing on the plastic tab located in the rinse aid compartment.

F LEDs 2, 4, 5, 6 and 9 are lit. The Whirlpool SMA “brain” receives signals either when the tank is empty or when it is full. Most likely, cleaning or replacing the pressure switch will help.
F The second, third and ninth lights flash. The equipment informs the user that the system that controls the volume of water in the tank is not functioning. The full drum alarm lasts longer than one minute.
F Four indicators are lit: 2, 3, 5 and 9. The self-diagnosis system informs that the engine does not turn. The reason may be either in the motor itself or in the control module.
F The glow of lamps 2, 3, 5, 6 and 9 is observed. The technology signals that the electric motor rotates in only one direction. The motor relay on the board has probably burned out.
F Indication numbers 2, 3, 4, 9 are on. The electric motor is malfunctioning - it spins up to insufficient speed, or does not begin to function at all. The cause of this malfunction is usually the stator winding relay. You need to install a new part.

As you can see, the same error can indicate different failures.Therefore, it is necessary to carefully understand the problem and conduct additional diagnostics of the equipment. The explanation of the fault codes is presented in the instructions for the washing machine. Whirlpool.

Special codes

In addition to the main one, there is an additional list of error codes issued by the Whirlpool technique. It is also presented in the user manual. Let's figure out what malfunctions and malfunctions in the equipment we are talking about.

FH(F01). Only the first LED is lit. The machine notifies that water does not “enter” the system. There may be several reasons for this: low pressure in the pipes, a closed shut-off valve, a clogged inlet valve, self-draining (if the drain hose is connected incorrectly, the tank fills and then empties). In addition, the problem may lie in a broken level sensor, damaged wiring, or a malfunction of the electronic module. The algorithm of actions for repairing the washing machine will be different in each case.
FA(F02). Lights 5 and 9 are observed blinking. This means that the “Aquastop” function has been activated. Most often this happens due to a leak. Depressurization of the system is observed when the tank is damaged, the cuff of the hatch door is defective, pipes are broken, etc. Less commonly, the problem is a malfunction of the control module.

If the Whirlpool machine is leaking due to a “cracked” tank, it is more advisable to refuse to repair the unit and think about purchasing a new washing machine.

FP (F03). Indicators 5, 6 and 8 light up at the same time. The machine informs about a failure in the drainage system - the liquid is not discharged from the tank into the sewer. Possible causes: pump failure, clogged drain hose or garbage filter, damage to the main control board.
Fod (F18). Lights 2, 5 and 9 light up. The machine stops working due to excessive foaming.It is possible that the wrong powder is used or the dosage of detergent is greatly exceeded. You need to turn off the device, wait until the “soap” cap disappears and drain the water from the system by starting the appropriate mode.
FDL. The washing machine indicates that the door lock device is broken. You'll have to inspect the contacts of the blocker. If everything is fine with them, you need to replace the UBL.
FDU. The hatch is not closed tightly enough. You can try pressing the door with your knee and the lock will work. If it doesn’t help, the UBL needs to be replaced.
bdd. The code is typical for “verticals”. LEDs 2, 3, 4, 5, 6 and 9 are lit. The unit informs about poorly closed drum flaps. You should proceed as follows: hold down the “Reset” button for 3 seconds. The drum should open. Then lift the washer lid, close the doors again and activate the desired mode.
F A very rare code found only on modern Whirlpools. Informs that the software has not been updated via the Internet. In this situation, you should contact your provider or service center specialists.

Deciphering errors will help narrow down the range of possible breakdowns. This will make it easier to bring the machine back to “life.” Depending on the complexity of the upcoming repair, you should decide whether to do the work yourself or call a service center.