Bosch Maxx 5 washing machine errors

Bosch Maxx 5 washing machine errors Undoubtedly, to fix some problems in Bosch washing machines, it is necessary to call specialists, but in some cases, any average person can cope with the problem on their own. So, in order to understand when you need to sound the alarm, and when you just need to be patient and time, you need to know the list of errors of the Bosch Maxx 5 washing machine. As a rule, no one stores the instructions, or the information in them is incomplete, so it needs to be systematized .

Decryption problem

The difficulty is that not all housewives even immediately understand what exactly happened, simply not knowing how the machine that produces the error code behaves. Of course, on units with a display everything is simple and clear - I looked at the combination, found the value, and thought about what to do next. But what about those whose models are not equipped with a screen? In this case, the diagnostic system also works, but somewhat differently, namely by flashing lights on the control panel. Accordingly, when the machine freezes, and chaotic blinking is the only reaction to the user’s actions, panic appears. determine the error

Here you need to calm down and carefully observe the diodes. You need to write down which keys are lit or blinking, and if they are blinking, then in what order and at what interval. And only after that, open the instructions, manual or other document where the meanings of fault codes are collected, you will probably find the one you need. How to proceed next is another question, perhaps on your own, and perhaps with the help of professionals.

Diagnostic system database

Despite the fact that there are not very many error codes for Bosch Max 5 washing machines, you don’t need to memorize them all by heart; keeping this kind of information in your head is not easy - you will inevitably miss something and make a mistake. Just write out or print the guide and keep it handy. Here is a list of codes.

F16 on the screen, or the “Spin 800” indicator is permanently lit. The problem is most likely in the hatch door. Open the door and then close it, if necessary, press down lightly with your knee. Now try restarting the program.
The display shows F17, or the same “800 rpm spin” light and the indicator next to the image of a basin of water are on. Here the problem is in the collection of water: it either does not flow at all, or does so too slowly. There may be several solutions: clean the filter mesh, check the water pressure in the pipes. You can also open the faucet of the washing machine all the way.
Code F18 has a similar problem (analogue – the “Spin 400” and “Spin 800” lights are on). In this case, the water, on the contrary, does not drain or drains much longer than expected. Check the drain filter for contaminants and remove them, also check the pressure switch. If it is defective, replace it with a new one.
F19, or the following combination: basin with water, spin-800, spin-400. This indicates problems with water heating. It can either not heat up at all or literally boil. Here it’s all about almost 100% probability in the thermostat or heating element and its contacts. It is useless to repair these elements; it is easier to replace them with new ones. Voltage surges in the electrical network can also be the cause. Check the level to ensure it meets the standards.
Error F20 and the lighting of the spin-400 and spin-600 lights indicate a subtype of problem F19 - untimely heating of water.How to fix it - see the point above.
Error F21 and the spin-800, spin-600, spin-400 indicators and the basin icon light up simultaneously. This fault code indicates that the drive motor has stopped or is rotating unevenly. This leads to blocking the rotation of the drum, respectively. In this case, it is recommended to check three parts: the motor itself, the tachogenerator and the control module.
F22 or on machines without a display - spin bulbs 800, 600 and 400. Most likely, something has shorted inside the NTS sensor, or the wiring has burned out. Accordingly, the solution depends on checking and repairing/purchasing a new sensor.
F23 or the same three spin buttons 800, 600, 400 are lit along with the basin. This means that the presence of water was detected in the pan of the machine, and a leak occurred somewhere. To find out, inspect all parts that come into contact with water. It is also possible that the connecting circuits of the Aquastop system may break.
F40\the second light in the “Spin” column is on, as well as the top one in the right column. A rather complex error is a violation of equipment synchronization. Check the value of the machine's power supply; most likely, the indicators are off.
F63 the remaining spin lights are added to the previous indicators. There is only one way out - to reflash the electronic module or completely replace it with a new one.

As you understand, DIY repairs are not always possible; sometimes the help of a competent person is not even questioned. However, you should not think that you are involved in a complex adventure. It is enough just to regularly properly care for your equipment.

Attention! If the need for complex repairs does arise, do not attempt to carry them out without sufficient confidence in your knowledge and skills. Otherwise, further repairs will be even more expensive.