Whirlpool washing machine error codes

• Make sure the tap water supply is not blocked. That is, the valve is in the open position.
• Make sure the inlet hose is not kinked or clogged. Inspect the fill valve strainer. It is located at the junction of the hose and the machine.
• Make sure the fill valve is working properly.

If there is water in the machine tank:

• Make sure that the pressure switch tube is not clogged and is securely connected to the level switch and to the washing machine drum.
• Make sure the drain pump is not broken.
• Make sure that the pressure switch is working properly.
• Make sure that the electronics module has not failed.
• Make sure that the pressure switch (level sensor) is functioning properly.
• Inspect the siphon for blockages.
• Inspect the hoses for possible water leaks.

• Make sure the drain pump is not broken and is working properly.
• Inspect the wiring and contacts.
• Inspect and clean (if necessary) the drain pump filter.A blockage may prevent water from draining.
• Make sure the drain hose is not pinched, kinked or clogged.
• If you have done everything, but when you start the wash, this error occurs again, then you should replace the pump.

• Make sure that the sensor is securely connected to the heating element and relay.
• Make sure the sensor is working properly.
• Make sure the heating element, its wiring and relay are working properly.

• Make sure the washing machine motor is working properly.
• Make sure there is no open circuit between the engine and its control panel.
• Make sure there is no open circuit between the engine control panel and the electronics module.
• Make sure the motor control panel is in good working order.
• Make sure the wiring is intact.

• Make sure the motor control panel is working properly.
• Make sure the electric motor is in good condition.
• Make sure there is no damage to the wiring.
• Make sure that the contacts between the engine and its control panel are working properly.
• Make sure the contacts between the motor control panel and the main control panel are good.

• Make sure that the wiring and contacts of the drain pump, control panel, and pressure switch are in good condition.
• Make sure the drain pump filter is not clogged.
• Check the drain hose. It should not be pinched or clogged.
• Make sure the drain pump is working properly.
• Check the pressure switch (level switch).
• Make sure the fill valve is working properly.

• Check the engine.
• Make sure the engine control panel is in good working order.
• Check the location of the washing machine. It should not be located near the battery. It is also desirable to have ventilation in the room.
• Make sure the contacts and wiring are in good condition.
• Make sure that moving parts are not damaged.

• Make sure moving parts are not worn and are working properly.
• Check wiring and contacts.
• Make sure the electric motor is working properly.
• Check the engine control panel.
• Make sure the central control panel is not broken.

• Check the metering motor.
• Inspect the dispenser and its motor for mechanical damage.
• Make sure the contacts and wiring are in good condition.

• Make sure the main control panel is working properly.
• If the reason for the occurrence was a voltage surge, then perhaps turning off the machine for a couple of minutes and turning it on again will help.

• Make sure wiring and other connections are intact.
• Check the washing machine motor.
• Make sure the drive belt is in place and not worn.
• Check the motor control panel.

• Make sure the drain pump and pressure switch are working properly.
• Check the drain hose for kinks or blockages.
• Make sure the main control panel is working properly.
• Make sure there are no blockages in the drain pump filter.
• Check the wiring and contact tightness.

• The lock is faulty or missing.
• Make sure that the contacts and wiring of the drain pump, the main control panel and the persostat are intact.
• The UBL (washing machine hatch locking device) or its wiring may be damaged.

• Check the wiring from the control panel to the UBL.
• The lock may fail.
• Also make sure that there are no foreign bodies in the lock mechanism and UBL.
• Make sure that the UBL (hatch locking device) is working properly.