Haier washing machine error codes
Haier washing machine error codes are nothing more than a means of communication between their self-diagnosis systems and the user. If the washing machine suddenly has some kind of malfunction, this system will display a special code, deciphering which the user will be able to roughly understand what is broken and take action. It turns out that we need, first of all, to figure out how the error codes of Hayer washing machines are deciphered, and that’s what we’ll do in the framework of this publication.
User generated problems
In some cases, the user himself becomes the reason why the Haer washing machine stops washing and displays some kind of error on the display. Anything can happen, the user forgot to pour powder into the tray and starts washing without powder, overloaded the drum with laundry or distributed the laundry in the drum incorrectly, well, let’s not make a “semantic confusion”, let’s list these errors and briefly describe them.
- No salt. This inscription, also known as an error code, eloquently notifies the user that there is no powder in the tray. If you
If you are sure that you poured powder, then most likely the powder receiver channel is clogged. In more rare cases, the washing machine Haier mistake No salt reacts to low quality powder. - UNB. This code alerts the user to an imbalance within the drum. As a rule, an imbalance occurs due to the fact that the user has incorrectly distributed the laundry in the drum when putting it in before washing. Sometimes an imbalance occurs because the user washes one bulky and heavy item.
Often, an imbalance can occur due to insufficient or, conversely, excessive loading of the Haier washing machine drum.Try to load the drum correctly.
- ERR1 This error occurs when the machine cannot start washing due to the hatch not being closed. The main reason is that the user simply did not press down the hatch tightly, and accordingly it did not close, and an error popped up. But often this error is caused by a broken hatch locking device or a broken latch on the hatch door.
Problems with filling and draining water
Breakdowns associated with the inability to fill the tank of the machine with water or, on the contrary, drain the water, occur quite often; one can even say without exaggeration that they are the most common. That is why in the self-diagnosis system of the Haier washing machine, there are so many codes dedicated to water-related faults, let's list them.
- ERR2 The appearance of this code is due to the inability to drain water from the tank within the 4 minutes specified by the program. There are several reasons for this: the pump is clogged or broken, the drain hose is bent incorrectly, or the drain hose is twisted or broken.
In some cases, ERR2 pops up when there is a power failure to the drain pump of the Haier washing machine.
- ERR5 Indicates that it is impossible to pump water into the tank of the Haier washing machine. The washing machine must pump water to the level set by the program within a maximum of 8 minutes; if this does not happen, this error appears. Why does this happen? There are several options: the water pressure is very low, the tap is closed and therefore water supply is impossible, the filling valve mesh is clogged with debris, the power supply to the filling valve, pump or pressure switch is interrupted.
- ERR8 This code indicates that too much water has accumulated in the machine’s tank. In such a situation, in 97% of cases the culprit of the error is a faulty pressure switch.In much more rare cases, this code generates a burnt-out triac on the control board, which controls the water level sensor.
- ERR9 No matter how strange it may be, this code is deciphered in the same way as ERR8, with the only difference being that ERR9 is generated by other reasons. In particular: the filling valve has burned out, so the module cannot stop the supply of water to the tank, the triac that controls the filling valve has burned out.
- ERR10 This error is also associated with a malfunction of the washing machine’s hydraulic system, but unlike the codes described above, in our case the filling valve functions normally, but the pressure switch is broken in 99% of cases.
Problems with water heating
Now let's talk about errors related to heating water in a Haier washing machine. Let's list these codes and then decipher them.
ERR3. Literally, this error code can be deciphered as: “... the heating element is not able to heat the water to the temperature set by the program...”. This error also appears if the heating element does not heat the water at all. The main reasons: the temperature sensor has burned out or the power supply to the temperature sensor has been interrupted.
ERR4. This code is deciphered in exactly the same way as the ERR3 code, although the reason for the appearance of ERR4 is not a burnt-out temperature sensor, but a burnt-out heating element. In addition, if the power supply to the heating element is interrupted and it does not turn on, error ERR4 appears.
Electrical and electronics
A modern automatic washing machine from the Haier brand is absolutely crammed with electricity and electronics. A large amount of wiring, tied into bundles, is designed to power dozens of sensors and modules that ensure the functioning of the machine. Well, the electronic module controls this entire complex system, ensuring its functionality.If any of this fails, the washer’s self-diagnosis system will warn the user by issuing one of the following codes.
ERR6. This error tells us about a malfunction that has occurred on the control module board. There can be a lot of reasons. One of the tracks may be damaged, one or more semiconductor elements may fail, or the contact between the track and such an element may fail.
In slightly more rare cases, this error occurs if one or more wires in the block suitable for the control module board connector are not seated tightly, causing contact to be lost.
ERR7. You don't see this code very often. It tells us that several parts of the control module have burned out at once and this malfunction is critical. This can happen, for example, as a result of a short circuit. ERR7 is a more serious problem than ERR6.
EUAR. This is another serious malfunction that usually occurs in the control module. In more rare cases, this error occurs when a whole bundle of wires suitable for the electronic module burns out.
Troubleshooting
Now it's time to talk about eliminating the causes of the above errors. We will talk, of course, in an overview, without details, since there are special thematic articles for a detailed description of the elimination of all malfunctions.
If the message No salt appears, you need to check whether there is powder in the tray or not, or clean the powder receptacle channel, or change the powder to a better one. Has the UNB code appeared? Stop the wash and distribute the laundry inside the drum of your Haier washing machine and start the wash again. If you encounter error ERR1, try pushing the hatch with your knee without turning off the washing machine. Often this measure helps to start the wash.If this doesn't help, you'll have to repair the washing machine hatch locking device.
When ERR2 code appears, check the drain hose. Perhaps it was bent incorrectly during installation or clogged, which is why the water does not drain out. If everything is fine with the hose, you will have to climb into the housing, remove the drain pump and clean it of dirt. At the same time, you will need to check it with a multimeter for malfunctions and if any are found, replace the part. If you encounter error ERR3, feel free to remove the back wall of your Haier washing machine and check the temperature sensor and the wiring that goes to it with a multimeter. Most likely, the sensor will have to be replaced.
ERR4 will force you to check not the temperature sensor, which, by the way, is installed on the heating element, but the heating element itself or the wiring. The one that approaches him. First of all, you need to measure the resistance of the heating element, then take on the electrics that power it. If error ERR5 occurs, you need to check whether there is water in the water supply and whether all taps are open. If water is supplied but does not enter the washing machine, you need to remove and wash the filter mesh that is located on the inlet valve. Well, if this doesn’t help, you’ll have to check the fill valve, pressure switch and pump one by one with a multimeter.
When faced with error ERR6, you can reboot your Hyer washing machine by unplugging it and turning it back on after a couple of minutes. If this measure does not help, feel free to call a technician, since you are unlikely to repair the control board yourself. By the way, the ERR7 code should prompt you to take the same actions as in the case of the ERR6 code, however, in this situation you need to mentally prepare for serious costs.
The ERR8 code lets us know that it’s time to check the washing machine’s pressure switch. Start with his pipe.It needs to be blown out and carefully cleaned of dirt, after which it needs to be checked with a multimeter. If you encounter an error ERR9, feel free to check the intake module with a multimeter. First, inspect the intake valve itself, it may be clogged with dirt and cannot open and close normally, then check the electrics. If necessary, the inlet module must be replaced.
And finally, when faced with the ERR10 error, open the top cover of the Hyer washing machine and carefully check the pressure switch and the electrics powering it. First, check the resistance of this part with a multimeter, and then check the wiring supplying it for breakdown.
In conclusion, we note that the Haier washing machine, like any other modern automatic washing machine, has a self-diagnosis system that “communicates” with the user through a special code system. To “understand” a washing machine, you need to know the decoding of the codes of this system. Actually, we presented this transcript in this article, we hope this information will be useful. Good luck!
Interesting:
73 reader comments
Haier shows EUAR error, not a single workshop will undertake repairs. Everyone has the same opinion, this brand of washing machine is disposable! Cannot be repaired.
Can this really happen?
You just need to think with your head and contact their service, and not run around private offices.
Wires are shorted in the braid to the control module
The inscription LOCH was displayed during washing. And not a single button works.
Check the filter
This is the manufacturer subtly hinting at who he sees his clients as.
Hello. The type of mode on the washing machine flashes when turned on. You select a program, it blinks. Turn on -
stops blinking. What could it be?
Same nonsense. It doesn’t seem to affect performance, but it’s a little annoying (
Same problem... Didn't find a solution?
The Loch error was displayed. And it smells like burnt wiring. Is this normal?
Error #10, the drum does not open. I washed without laundry, because... my son poured a liter of mouthwash into it. What to do? Washing machine Haier HW 60 1082s.
Error ERR2, how to fix it? When washing on any mode, the drain works for a long time, and then it starts to squeal. You press start and it starts working again. This error keeps appearing.
Error E1 is on. The filter has been cleaned, but when starting, the machine does not allow you to select a new program and starts an incomplete program. Then it throws this error.
During washing, the machine stopped and LOCH was displayed.
We have E1 lit on the display. There is no decryption in the instructions.
E4 issues
We have E4 lit on the display. There is no decryption in the instructions.
Tell me, how did you deal with error e4?
We have E4 lit on the display. From the very beginning 🙁
ERR7 on Haier HW60-B1286S. Heating element error. Our heating element burned out.
Hello, when you turn it on, the text “end” lights up on the screen, then “lost”, what does this mean? The machine does not work and the door is locked and will not open.
I have the same thing, how did you fix it?
How did you fix it?
Hello, please help. When turned on, the HAIER washing machine displays END and does not allow the program to start. If you start switching programs it displays clot. I didn't find anything like that in the errors.
Hello, please tell me, the machine shows error er16.
Smart people say that this is most likely a malfunction of the electronics module. It's better not to dig on your own. Call the master. I think the repairs will cost a lot.
SMA Haier hw50-12866me. There is no water flow between the 220V network zero and the neutral (ground) of the control board, the multimeter showed 3 ohms (the hatch door is open) and 9 ohms (the door is tightly closed... it looks like a short circuit. Or... what?
And if the display shows fco, what does that mean?
Hello, Ekaterina, I wanted to ask about the washing machine, did anyone answer you? They also show FOC. I don't know what it is. I can't find the reason anywhere.
Hello. Error E1 appears on the screen, what does this mean?
Error fa4 is on with a characteristic sound signal. What could it be?
err 10 sometimes happens if you do not close the door, then close it and do not restart the washing program.
Hello, what does FC2 stand for?
Hello! Did you figure out what the reason is? My FC2 light is also on.
I have FC1. Did you manage to solve the problem?
My Haier 1082 S machine is flashing Err7. Tell me, what is this?
After washing, the Haier HW60 machine went crazy and says end unb, but after unloading it does not understand that it has been unloaded and now screams every time it is turned on and does not wash. Unplugging doesn't help.
We have the same. Have you solved the problem?
Good afternoon, what did you do?
The error is written by RTUO
FCO lights up on the display and does not turn on. Bought 2 weeks ago. Unplugging doesn't help.
Svetlana good evening! Did you find out the reason for FCO?
Hello, my E1 is blinking, what should I do? Now it doesn't work completely. It wasn't even a month since we bought it. Please tell me what to do?
Error F6 on a Hier Intilus washing machine, what does it mean?
The machine displays “FC0”, what should I do?
Hello, if the Haier HW60-1229AS machine washes and stops at a certain time. It gives Loct and that's it. How to drain the water and open it, what should I do?
I see FC2, what does that mean?
Thank you, it helped a lot. Found the problem after reading your site.
Thank you, your site is just super! Helps solve all problems when not addressed, you always have everything! With thanks.
Hello, help me! I get the error Egg8, what should I do?
Hello, please help. When turned on, the HAIER washing machine displays END and does not allow the program to start. If you start switching programs it displays clot. I didn't find anything like that in the errors.
Svetlana, hello! Have you solved the problem? We just have the same one. Can you please advise? Thank you in advance!
Hello, you did not solve this problem, we have the same one :)
Tell me what the problem is with Hayer, when you turn it on, a message appears for 2 seconds. UA, SH or maybe it's 5H.
Hello. On Haier HWD80-B14686 it periodically, but precisely at the end of the wash, gives f4 (water heating error). Should I start watching TEN?
Hello, if the Haier steam +fresh machine washes and stops at a certain time. It gives Loct and that's it. How to drain the water and open it, what should I do?
First, unplug the power from the outlet. And then check the hatch. We got a nylon sock.
Haier error code cLot. You need to simultaneously press the Delayed start + i-time buttons (this is a child lock) and simultaneously press the button that selects the mode. Maybe it will be useful to someone :)
Hello, please help. When turned on, the HAIER washing machine displays END and does not allow the program to start. If you start switching programs it displays clot. I didn't find anything like that in the errors.
Hello. The screen of the Haier washing machine shows lost and the doors are jammed, tell me what to do..
Brilliant! Thank you
Thank you very much! There was no need to call a technician!
We simultaneously pressed the Delayed Start and I-time buttons and scrolled through the program selection. And the child lock program immediately turned off and the door opened!
Haier machine. The End and Loch buttons alternately interfere. The hatch won't open, what should I do?
Hello, error code fc2, how to fix it?
The Haier HW60 1029AN machine displays the lost sign. I haven’t finished washing it, we can’t open the hatch. Tell me what to do?
Hello. The Haier HW60 machine gives End errors after washing. When you switch modes, you get a cloh error. The hatch is locked. Disconnecting the power supply did not help, I checked the filter. How to open the machine and clear the error?
Hayer displays error E2 (the instructions indicate to close the door). The error continues to appear even after being unplugged.
Hello, I have a problem. The machine pumps water and tugs the drum a little, but does not spin it. What could be the reason?
Haier machine. The End and Loch buttons alternately interfere. The hatch won't open, what should I do?
Hello. At the end of the wash I got the code sby. I don’t understand what this means. There is no information anywhere.
I also have SBY, there is no information anywhere, I bought it today and washed it twice, but after finishing the program, it gives an error. Where can I find the answer?
Hello, please help me, on my Haier car, End and Loch are displayed, the hatch does not open, what should I do?
The machine displays error E4. The hose was changed and the filter was cleaned. The problem has not been resolved. First it takes water for about 5 minutes, and then it gives an error.