Error codes for Atlant washing machines
Most new home appliances have several important features.
In addition to their direct functions, they also inform about what kind of breakdown prevents them from working normally!
Let's move on to a description of washing machine error codes.
Error codes
| Error Alarm | Decoding | Fault options | Repair |
| On a machine with a display "Sel". On a machine without a display: the indicators do not light up | Interface module selector failure | The potentiometer that selects programs may be damaged. | Changing the interface module. |
| On display: "None". If there is no display, all indicators light up. | Excessive foam formation. | Too much washing powder has been used. | Limit the amount of washing powder to a smaller amount. |
| Incorrect mode specified. That is, a mode with an excessive amount of water poured. | Select a washing mode that is designed for this type of fabric. | ||
| Washing powder or other detergent not suitable for machine washing was used. | Use only those products and powders that are intended for automatic machine washing. | ||
| Display: "F2"The third diode lights up. | The temperature sensor has failed | Problems with the wiring and contacts of the temperature sensor or module. | Make sure that the wires and contacts are in good condition. |
| The temperature sensor is damaged. | Change the heating element (heating element). | ||
| The control module has failed. | Replace the faulty module. | ||
| Display: "F3"The 3rd and 4th indicators are lit. | The heating element of the washing machine (heating element) has failed | Damage to the heating element. | Replacing the heating element (heating element). |
| Broken contacts or wiring. | Make sure the wires and contacts are in good condition. | ||
| The control module has failed. | The module needs to be replaced. | ||
| On display: "F4"2nd diode lights up | Damage to the drain pump (pump) | The drain hose is clogged or pinched. | Straighten the hose, find and remove the blockage. |
| Incorrect hose installation. | Reinstall the hose as required by the instructions. | ||
| If a foreign object gets into the pump, its impeller will become stuck. | Remove the trapped object and check the rotation of the impeller. | ||
| Drain pump failure. | Replace a broken pump. | ||
| The ball is stuck in the drain coupling. | Drain the water from the machine using a tube and change the coupling | ||
| The drain coupling is clogged. | Perform cleaning. | ||
| Problem with wiring and contacts. | Make sure both are in good working order. | ||
| The electronics module has failed. | Change the electronics module. | ||
| Display: "F5"The 2nd and 4th indicators are lit | Fill valve failure | The water inlet hose filter is clogged. | Cleaning the filter. |
| The inlet hose is clogged or kinked. | Unscrew the hose from the machine. Run water to check. If necessary, clean the hose. | ||
| There is no water in the water supply, the water supply to the tap is not open, or the fill valve is broken. | Make sure the valve is in the open position. Make sure the water supply is not turned off. If necessary, replace the valve. | ||
| Open circuit between the control module and the fill valve. | Using a tester, verify the presence or absence of a break. | ||
| Fill valve contact failure | Make sure the contacts are in working order. | ||
| Control module failure. | Replace it with a new one. | ||
| Display: "F6"2nd and 3rd indicator lights up | Problems with the washing machine motor relay | Overheating of the stator winding. The contacts responsible for the temperature protection of the engine are disconnected. | Change the engine of the washing machine. |
| Display: "F7"Lighting: 2nd, 3rd and 4th indicators | Electricity problems | Noise filter failure | It needs to be changed. |
| The voltage in the network does not correspond to the required one (more or less). | Check the network using a tester. | ||
| The control module is broken. | Replace it. | ||
| Display: "F8"Indicator No. 1 lights up | Too much water in the washing machine tank | Pressostat failure. | Replace the pressure switch. |
| Fill valve stuck. | Replace the valve. | ||
| Problems with the wiring or contacts of the pressure switch and control module. | Make sure that the wires and contacts are in good condition. | ||
| Violation of the tightness of the cylinder. | Check the cylinder. | ||
| The control module is broken. | Replace it with a good one. | ||
| Display:"F9"Indicators No. 1 and No. 4 are lit | Problems with the engine tachometer | Poor contact or wiring of the electric motor or control module. | Make sure there is a problem or not by checking the wires and contacts. |
| The engine or tachogenerator is broken. | Change the engine. | ||
| The control module has failed. | Replace it with a working one. | ||
| On display: "F10" If the machine does not have a display: indicators No. 1 and No. 3 light up | Failure of UBL (blocking) | Locking fault. | Replace it with a new one. |
| Control module failure. | Replacement. | ||
| Display message: "door"The 1st, 3rd, 4th indicators light up | Possible lock failure (UBL) | No contact in blocking . | Make sure that the wires are connected correctly and there are no breaks. |
| The hatch is not locked tightly enough. | Lock the hatch again. | ||
| The door or lock is warped. | Straighten the hatch/lock. | ||
| An open circuit between the control module and the UBL. | Use a tester to test the circuit. | ||
| Lockout connector problem . | Make sure the wires are properly connected and intact. | ||
| The control module has failed. | Change it. | ||
| Display: "F12"1st and 2nd indicators are lit | Possible breakdown of the triath engine | The engine of the washing machine broke down. | Carry out replacement. |
| Break in the motor winding. | Replace the engine. | ||
| No contact. | Make sure the wires and connector are in good condition. | ||
| The control module is broken. | Change it. | ||
| Display "F13"1st, 2nd, 4th indicators are lit | Various breakdowns | Problems with wiring or contacts. | Check wires and contacts. |
| The control module is broken. | Replace with a new one. | ||
| On display: "F14"1st and 2nd indicators | Program crash | The program crashed. The electronics module is incorrectly programmed. | Replace the module. |
| Display: "F15" | Water leak detected | The tank has become depressurized. | Replace it. |
| Leak through a closed door | Change the hatch cuff. | ||
| Violation of sealing of the drain hose, pipes, drain coupling | Try to determine the location of the leak and fix it. Make sure that the clamps secure the pipes well enough. Make sure the pipes and drain hose are intact. |
Interesting:
18 reader comments
The Atlant washing machine has been working for me for the 5th year. No complaints. If I change my car, it will only be to Atlant. Atlant bought a refrigerator from me in 2010. No complaints either, it works great. Keep it up guys.Well done. I myself am from Donetsk. Thank you for the good products.
This is the third module failure in two years!!!!
It all depends on karma, I also have an Atlant machine and a freezer. Everything is working
7 months error 15 service helpless
5 years old machine - not a single breakdown. just a little noisy. Also a refrigerator. Well done!
Atlant machine - everything was fine for 6 years. During the next wash I turn it on and it lights up - the end of the program and the lock. And it doesn’t clean up or start. What to do? Help!
It worked for 4 years and that’s it, the module flew. They replaced it, then they soldered the tank. In general, there is nothing more to repair. It's better to buy a new one. I understand that now all the washing machines are no more than 5 years old and everything is new. This is the policy.
I do not know what to do. The machine gives error F8, it worked perfectly before shutting down, I took it as a spare because I need a large washing machine for constant washing. Now the main one is broken and this one indicates that there is a lot of water in the barrel, although this cannot be. She stood for 4 years.
Error f16, what is it?
The Atlant machine throws error f13. Indicators 3,4,6 are lit. What to do, what is the reason? Tell?
Error n appears, what does this mean?
This is not an error, but the night wash mode.
No karma! In 1.5 years, a washing machine breaks down 4 times.Before this I managed without a technician, but now I can’t even find the error code P. Thank you, domestic manufacturer!
Hope, “n” is not an error, but the “night wash” option is enabled. There is a button on the panel - you can use it to turn the option on and off :)
f13 – change the control module, the firmware has crashed.
f16 – heating did not turn off. Change either the control module or the heating element. What exactly cannot be diagnosed remotely.
The display shows an error P. The door is locked. What to do?
The display shows n-24