Where is the heating element in a Samsung washing machine?

Where is the heating element in a Samsung washing machine? If you suspect damage to the heating element of the washing machine, you need to diagnose it as soon as possible. To do this, you must gain access to the heater. Which side should you approach the machine from to find the part? Let's figure out where the heating element is located in the car, how to inspect it, check it and, if necessary, replace it.

Looking for a heating element

To remove the heating element from Samsung, it is not enough to simply remove the back panel, as, for example, this is done in Indesit or LG machines. In most Samsung models, the heating element is located at the front, so the removal process is somewhat more complicated. On the front wall of the machine there is a control panel, a dispenser, and a hatch door. All components will have to be removed, and this will take more time than unscrewing several bolts of the back wall.

But this arrangement also has its advantages. During the work, you will not have to move the machine from the wall or disconnect the machine from the water supply and sewerage.

So, having figured out the location of the heating element in a Samsung washing machine, you should also understand the principle of removing the element. The algorithm of actions will be as follows:

de-energize the equipment;
unscrew the garbage filter to collect the water remaining in the system;
pull out the powder receptacle (the part can be easily removed by pressing the button located inside the cuvette);
Unscrew the screws that were located under the dispenser;
tighten the bolt on the control panel;
Place the panel, without removing it from the body, on the top of the machine;

The control panel must be moved very carefully so as not to disturb the wiring.

unscrew 3 more bolts located under the removed panel;
open the hatch door;
use a slotted screwdriver to hook the clamp securing the cuff,
tuck the outer edge of the sealing rubber into the drum;
remove the bottom “false” panel by loosening the fasteners.

After these manipulations, the front wall of the washer will only be held on by a pair of hooks. To remove the front cover, grasp the bottom of the cover and pull the panel up. It is important not to overdo it, remove the wall carefully so as not to disconnect the wiring of the locking device. You just need to move the front panel slightly to open access to the heating element.

Afterwards, you can move the control panel down so that it does not fall from the top cover during further manipulations. This will complete the preparation for diagnosing the heating element.

The heating element is located in the washing machine directly under the tank. There is no need to rush and change the part right away; first of all, you need to check the heater. Only after making sure that it is faulty should you install a new element.

Testing the part

As already mentioned, the first step is to diagnose the heating element. It is possible that the heating element is working properly, but the water does not reach the required temperature due to the failure of the control module. To check the heater you will need a special device - a multimeter, in other words - a tester.

The diagnostic algorithm will be as follows:

switch the multimeter to resistance measurement mode;
disconnect the wires from the contacts of the heating element and thermostat (the thermistor is located directly on the heater). It is important to remove the wiring carefully so as not to disturb the connection diagram. Before disconnecting the wires, it is recommended to photograph their position so as not to make a mistake during reassembly;
Apply the tester probes to both contact terminals of the heater;
evaluate the performance of the element. If the device screen displays a value within 25-30 Ohms, then the part being tested is in perfect order.

When the multimeter display shows “0” or “1”, it means that the heating element has burned out and can no longer perform its functions. In such a situation, it is necessary to replace the element.

We purchase and exchange

The heating element of the washing machine cannot be repaired, so if it breaks, there is only one way out - install a new heating element. You must purchase a replacement part carefully. It is important to buy a heater that matches the specific Samsung washing machine model.

If you have doubts when selecting a heating element yourself, it is better to remove the part and take it to the store to choose a similar one.

If you know exactly what spare part you need, you can look for it in online stores. Often prices on online platforms are much lower. However, you should not buy components with a very low cost; they may be defective. On average, a heating element for Samsung costs about $8-15.

The power of the heater is of great importance. Typically, heating elements, depending on the model of Samsung equipment, are characterized by a power of 1850 or 1900 W. To change the heating element, remove the front wall

Having selected a replacement part and dismantled the front wall of the machine, you can begin to change the element. Let's figure out how to do this:

loosen the nut securing the heater. A socket wrench will help with this. The mount is located in the middle of the shank;
grab the part to be dismantled and loosen it;
Use a wrench to tap the stud (the rod on which the nut was screwed). The pin should go inside;
use a slotted screwdriver to pry the heating element, trying to move it from its seat;
pull the contacts to remove the heater from the groove. It is important to remove the part carefully; if you break off the contacts, the removal process will become noticeably more complicated.

Pull out the heating element and see what condition it is in. Most often, its surface is covered with scale, and if a short circuit occurs, dark spots will be visible on the heating element.

Subsequent installation of the component will not take much time; you must:

Use a multimeter to check the new heating element, make sure that the contact resistance is normal. This way you will exclude factory defects of the spare part;
treat the heater with a special lubricant or aerosol product WD-40;
place the part in the groove;
secure with a central nut;
put the thermostat back in;
connect the power supply.

In fact, you can fix a breakdown of a Samsung washing machine caused by a failure of the heating element with your own hands, without the help of a specialist. Repairs do not require any specific knowledge, and the tools that will be needed during the work process can be found in every home. It is enough to carefully study the instructions for action and strictly follow them.